Honeywell Door 5828 User Manual

K0021 3/03 Rev. B  
$'(0&2ꢀꢁꢂꢃꢂꢄꢁꢂꢃꢂ9ꢀ  
:LUHOHVVꢀ%LGLUHFWLRQDOꢀ)L[HGꢅ:RUGꢀ.H\SDGꢀ  
USER GUIDE  
GENERAL INFORMATION  
KEYPAD KEYS  
The 5828 and 5828V are wireless keypads that can be  
used to operate and get status from your security  
system. The 5828 and 5828V have the following  
features (voice annunciation features apply only to the  
5828V):  
These keypads include 12-operational keys, as well as  
four Special Function keys that are backlit for ease of  
use when the keypad is active. To access the keypad  
keys, simply open the swing-down door by applying  
outward pressure on the door release slot on the right  
side.  
Can be used to arm/disarm, and perform other  
system operations.  
Panic alarms are activated by pressing the key pairs  
shown in the table below. Special Function keys A, B,  
and C, can be programmed by your installer to provide  
the same alarms by pressing a single key and holding it  
down for 3-seconds, or can be assigned other system  
operations. (Check with your installer for the  
availability and assignment of these keys).  
Can display and/or annunciate system status.  
Can automatically display and/or annunciate a  
change in system status if AC powered (e.g., for an  
alarm, the keypad will announce the type of alarm  
(fire or burglary) and location (e.g. kitchen window).  
Message Center can be used to record and play back  
a voice memo to yourself, or leave a message for a  
family member.  
Panic Alarm Key-  
Pairs/Special Function Keys  
Can be battery- or AC-powered (AC-powered units  
have several advantages, described below).  
[1] & [] or A  
[] & [#] or B  
[3] & [#] or C  
Battery-Powered Operation:  
SOUNDER  
The keypad’s built-in sounder pulses for fire alarms,  
and sounds continuously for burglary and audible  
panic alarms.  
HOW TO GET SYSTEM STATUS  
Turn on the keypad by pressing any numbered key.  
Status will be displayed within  
a
few seconds.  
AC-Powered Operation:  
Additionally, on AC powered units, the keypad is  
automatically updated when a change in system status  
takes place (arming, disarming, trouble, etc.).  
HOW TO PROGRAM OR CHANGE YOUR 4-DIGIT  
SECURITY CODE  
In order to Quick Arm the system using this keypad,  
you will need to program your own 4-digit security code  
into the keypad. This code must match a code that has  
already been programmed into your control panel. To  
program the 4-digit code, perform the following steps:  
key  
INSTANT  
CHIME  
keys at the  
Press the 7  
and 9  
NOTE:  
same time until the display flashes double dashes  
(- -), then release.  
[]  
Enter the 4-digit security code that matches a valid  
user code already programmed into your control  
panel. Do NOT use the Duress Code. There will be  
no display of the numbers you pressed.  
A
OFF  
MAX  
AWAY  
TEST  
CODE  
STAY  
BYPASS  
CHIME  
1
4
7
2
5
8
0
3
6
9
#
B
Press READY to accept your entry. The keypad  
will display the system status.  
INSTANT  
READY  
C
D
5828V Keypad with Front Cover Removed  
 

Harbor Freight Tools Portable Generator 69728 User Manual
Hasbro Games 32730 User Manual
Hasbro Robotics 6805280000 User Manual
Hoshizaki Ice Maker F 1000MAF C User Manual
Hotpoint Washer WMFUG 842 User Manual
Hotpoint Washer WMFUG 1063 User Manual
HP Hewlett Packard Laptop 4425S User Manual
HP Hewlett Packard Network Card Q6275A User Manual
HP Hewlett Packard Saw HP70100A User Manual
Humminbird Fish Finder 531571 1_C User Manual