iHome Clock Radio IA63 User Manual

Model iA63  
Stereo Alarm Clock Radio with  
Motorized Rotating Dock  
For Your iPhone or iPod  
works with  
iHome + Sleep  
alarm clock app  
iHome + Radio  
internet radio app  
Note: iHome+Sleep and iHome+Radio apps are not covered in detail in this booklet. To learn more about how  
these apps can enhance your experience, please download the free iHome+Sleep app from the App Store and  
review the Start Guide.  
 
Controls and Indicators  
Front Panel  
Snooze/Dimmer Button  
Stabilizer Lever  
Stabilizer  
Rotate Button  
iPod Dock  
Wakeup Button  
iPod Play/Pause Button  
Radio Button  
Bedtime Button  
Alarm Button  
Presets Button  
Set - Button  
Power/Alarm Reset/  
App Settings Button  
Set + Button  
Raise Volume Button  
Lower Volume Button  
Rear Panel  
Aux-in Jack  
Time set/Sync Button  
DST switch  
FM Antenna  
AC Adaptor Jack  
iA63 Display  
NOTE: PM indicator will not appear  
when clock is set to 24 hour display mode  
Time Display  
PM Indicator  
iHome App Indicator  
Battery Low Indicator  
FM Radio Indicator  
Alarm Indicator  
Sleep Indicator  
 
2
Quick Start  
2: docking your iPhone/iPod  
1: power  
Step 1  
Step 3  
RESET  
R E S E T  
1. Move the stabilizer lever to the right to release  
the stabilizer bar. 2. Gently dock your iPhone or  
iPod into the connector dock. 3. Press the  
stabilizer bar until it is snug against the iPhone or  
iPod. The iPhone or iPod will charge while docked.  
Attach AC adaptor cable to DC jack on back  
of the iA63 and plug the other end into a wall  
socket.  
Press the  
Button on the iA63  
to play your iPhone or iPod.  
3:rotating  
the dock  
Press the  
Button to rotate your iPhone or iPod to landscape mode. Press again to  
return to portrait mode. NOTE: please do not attempt to rotate the dock by hand, or to rotate  
the dock clockwise. The dock only rotates in the counter-clockwise direction when changing from  
portrait to landscape mode.  
3
 
Quick Start  
4: time sync  
Dock your iPhone or iPod (see step 3). Press and release the Time Set/Sync Button located on  
back of the iA63. “SYNC” will appear on the display, followed by the updated time upon successful  
syncing.  
5: FM radio  
Press the  
Button to select FM radio.  
Press the + or - Button to tune in a station.  
See page 8 for programming presets.  
4
 
Using the iA63  
Updating your iA63 firmware  
For best performance, make sure the iA63 firmware is up to date. To update, download the free iHome+Sleep app from the  
App Store to your iPhone or iPod touch. Turn on the iA63, dock your iPhone or iPod touch, launch the app and go to  
Settings/iA63 and follow the directions on your iPhone/iPod display to update the iA63 firmware if the display indicates that  
an update is available.  
Connect iA63 to Power Source  
Plug the AC adaptor cable into the AC Adaptor Jack on the back of the unit and the other end into a standard 220V AC wall  
socket. Adaptor must be plugged in to operate unit and charge iPhone/iPod. The iA63 does not operate on batteries (a battery  
back up system maintains clock settings during power failures).  
Installing/Replacing Clock Backup Battery  
The iA63 uses a CR2032 battery for backup to provide continuous alarm operation and clock settings in the event of a power  
failure. The battery is pre-installed with a battery pull tab. Remove the pull tab when you first start to use the iA63. If  
the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display  
backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset  
the time and alarm settings.  
Note: The Battery Low Icon  
is located at the left side of clock display. When the backup battery is low and needs to  
be replaced, the  
icon will flash.  
REPLACING THE BATTERY  
1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement.  
2. Place unit face down on a stable surface. Pull down and remove the backup battery compartment door located on the  
rear of the unit.  
3. Insert a new CR2032 battery by easing it under the tabs in the battery well and pressing  
down. Make sure the side marked + is facing up.  
4. Replace the battery compartment cover and stand unit back upright.  
Note: Make sure you dispose of battery properly (see your local regulations).  
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged,  
exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or  
other container containing metal objects, mix with used or other battery types, or store with  
hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws  
and regulations for transport and disposal.  
Setting Time Using iPhone/iPod Time Sync  
The iA63 Time Sync feature allows you to sync the time setting on the iA63 to the time from your docked iPhone or recent  
model iPod (iPod touch, iPod nano and iPod Classic; older iPod models such as iPod mini do not support this feature).  
1. Dock your iPhone or iPod  
2. Press and release the Time Set/ Sync Button located at the back of the unit. “SYNC” flashes on the display to indicate  
sync attempt.  
3. Once sync is completed,the updated time will appear on the display and 2 beeps will confirm successful syncing.  
4. If sync was not successful, “FAIL” will appear on the display and you will hear a long beep. If this happens, please try  
again, with a different iPhone or iPod if needed. If sync still fails, please see Setting Time Manually (page 6).  
NOTE: iPhone time is automatically updated to the correct time via cell phone towers. The time on your iPod is accurate  
only to the time on the computer the last time the iPod was synced to it. It’s possible to have up to 59 seconds difference  
between the iA63 and synced iPhone/iPod.  
 
5
Setting Up the iA63  
Setting the Time manually  
1. Slide the DST (Daylight Saving Time) Switch located on the back of the unit to +1 to add an hour (Spring) or to -1 to subtract  
an hour (Fall) to adjust for daylight saving time or standard time.  
2. Press and hold the Time Set/Sync Button located at the back of the unit until the time flashes on the display and the unit  
beeps once.  
3. Press the + or - Button to set the correct time (hold for faster setting). Remember to set the correct AM or PM time. The  
PM Indicator appears to the left of the time display; there is no AM indicator.  
4. If desired, press the  
button during Time setting to toggle the clock display format to 12 hours or 24 hours.  
5. When the correct time is displayed, press the Time Set Button again (or no button within 10 seconds) to exit the time  
setting mode.  
NOTE: You can also adjust settings on the iA63 via the iHome+Sleep app. To do so, press and hold the  
Button  
when the iHome+Sleep app is open and in view. See the iHome+Sleep Start Guide for more information.  
Using the Alarms  
iA63 lets you wake to FM radio, iPhone/iPod or buzzer alarm and to adjust the alarm volume.  
Setting the Alarms  
1. Press and hold the  
Button until the alarm time flashes on the display then release. Press the + or - Button to set  
the alarm time (hold for faster setting). Remember to set the correct AM or PM time.  
2. Press the Button again to confirm the set alarm time, then press the + or - Button to select an alarm source to  
wake to: iPod, Radio (the currently tuned radio frequency appears on the display) or Buzzer.  
For wake to iPod: select iPod to wake to a docked iPhone/iPod. If the unit does not detect an iPhone/iPod at the set  
alarm time, the iA63 will default to the buzzer alarm. The alarm cycle lasts for one hour; make sure you have enough music  
on your iPhone/iPod to last that long.  
For wake to radio: You can wake to a different preset station. After selecting Radio as the wake to source, press  
the  
Button as needed to cycle to the desired preset station (see Listening to Radio on page 8 for details on  
setting radio stations and presets).  
3. Press the  
4. Press the  
Button again, then press the + or - Button to set the alarm volume.  
Button again (or no button within 10 seconds) to exit the alarm setting mode. 2 beeps will confirm the  
alarm is set.The alarm is armed once set, indicated by the alarm icon on the display.  
Arming and Disarming Alarm (Turn Alarm Function On and Off)  
1. Press the  
Button at any time to arm the alarm. The alarm icon will appear and the currently set alarm time will  
appear briefly on the display.  
2. Press the  
Button again to disarm the alarm (the alarm icon will disappear).  
 
6
Setting Up the iA63  
Resetting the Alarm to Come on the Next Day  
1. When the alarm is sounding, press the  
the next day.  
Button or the wakeup button to stop the alarm and reset it to come on  
NOTE: Pressing the  
button when the alarm is sounding will cancel the alarm.  
Snooze Operation  
1. To program a custom snooze time, press and hold the Snooze Button during normal operation (when alarm is not sounding)  
until the snooze minutes display appears. You will hear beep, indicating Snooze settings mode. Press the + or - Button  
to set the snooze timer from 1 to 29 minutes. Press the Snooze/Dimmer Button to confirm snooze setting and exit snooze  
setting mode. You will hear 2 beeps confirming snooze time setting.  
2. Press the Snooze/Dimmer Button after an alarm sounds. The alarm will be silenced for the set snooze duration time then  
sound again. Snooze can be pressed several times during the 1 hour alarm cycle.  
Sure Alarm  
The iA63 has a sure alarm feature. If the back-up battery is installed, the buzzer alarm will still sound in the event of a power  
failure.  
Tip: Download the free iHome+Sleep app for advanced alarm, snooze and sleep functions  
Docking and Charging your iPhone/iPod  
1. Gently dock your iPhone or iPod. For added stability in landscape mode, slide the stabilizer lever (located at the top of the  
center rest above the dock) to the right to release the stabilizer, then press the stabilizer until it is snug against the side of  
the iPhone or iPod. While an iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until  
fully charged).  
Listening to iPhone/iPod  
1. Dock the already playing iPhone/iPod in Dock. The iA63 will automatically turn on and you will hear the music playing from  
your iPhone/iPod.  
Note: If the playing song volume is too low on the iPhone/iPod, the iA63 may not detect iPod is in play mode. Press the  
Button to play it.  
2. When an iPhone/iPod is docked and in standby mode, press the  
Button to play it. “iPod” will appear on the  
display to indicate iPod playing mode.  
3. Press the  
Button again to pause play; press again to resume it.  
4. Press the + or - Button to skip to the next or previous track on your iPhone/iPod. Press and hold the + or - Button to  
search within a track.  
5. Press the  
6. To turn off the unit, press the  
or  
to adjust the system volume.  
Button. An iPhone/iPod will continue charging while docked.  
 
7
Setting Up the iA63  
Rotating the Dock  
1. Before rotating dock, pull the spring-loaded Stabilizer Lever to the right to release the Stabilizer Bar, then press the bar  
in until it is snug against your iPhone or iPod  
2. To rotate a docked iPhone or iPod to landscape mode for viewing videos or movies, press the  
Button. Press  
again to return to standard upright portrait mode. To release the stabilizer bar, remove iPhone or iPod and pull the  
Stabilizer Lever to the right.  
NOTE: Rotation operation works only when the unit is connected to power source by AC adapter. Please do not  
attempt to rotate the dock by hand, or to rotate the dock clockwise. The dock only rotates in the counter-clockwise  
direction when changing from portrait to landscape mode.  
Listening to Radio  
Setting up the Antenna  
Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.  
Tuning and Playing the Radio  
1. Press the  
Button to turn on the iA63 in FM radio mode. The current radio frequency appears on the display.  
2. Press the + or - Button to tune the radio to a desired station. Press the + or - Button for a few seconds to scan for the  
next clear station.  
3. You can set up to 6 FM presets. To memorize a station as a preset:  
A. Press the  
B. Press the  
then hold the  
Button to enter radio mode (you can also press the  
Button as needed to step through the 6 presets (P1 - P6) to the number you wish to assign, and  
Button until the selected preset station begins flashing in the display.  
Button to go directly to a preset).  
C. Press the + or - Button to tune the radio to a desired station. Hold briefly to have the radio autoscan/search for the next  
clear station.  
D. Press the  
you wish to assign. Repeat steps A-D to preset up to 6 stations.  
4. To listen to a preset station, press the Button as needed to choose the desired preset.  
or Button to adjust the system volume.  
Button to confirm the setting. A confirmation beep will confirm the setting and the preset number  
5. Press the  
6. To turn off the radio (and the unit), press the  
Button.  
TIP: Download the iHome+Radio app from the App Store to enjoy thousands of internet radio stations from around the globe  
on your iA63.  
 
8
Setting Up the iA63  
Using the Aux-in Jack  
You can play any portable audio device with a standard 3.5 mm headphone jack through the iA63 via the Line-in Jack.  
NOTE: Do not play an aux audio device while iPhone or iPod is docked or you will hear both play at once.  
1. Plug one end of a standard audio patch cord (not included) into the headphone or line-out jack on your device and the  
other end of the patch cord into the iA63 Aux-in Jack located on the back of the unit.  
2. Turn on and play your device.  
3. Press the Play/pause Button on the iA63..  
4. Press the  
or Button to adjust the system volume. You may need to adjust the volume on your external device as well.  
6. To turn off the unit, press the  
Button. Please remember to turn off your device, too.  
Sleep Operation  
Sleep mode lets you sleep to your iPhone/Pod or radio, gradually lowering the volume until the unit shuts off at the selected  
time.  
1. Press the Bedtime Button to enter sleep mode. The sleep time will appear in the display.  
2. Press the Bedtime Button again as needed to adjust the sleep timer from 90, 60, 30, 15 minutes or OFF.  
3. When the display changes back to show the real time, press the Bedtime Button once to show the sleep time remaining.  
Pressing it again will change sleep time to next lowest increment.  
4. iA63 has an independent volume setting for sleep mode so you can adjust the sleep volume without affecting the normal  
volume. Press the  
or Button to adjust the sleep volume. The sleep volume will remain at that level the next time you  
enter sleep mode until controls are changed.  
5. To stop listening at any time, press the  
Button to turn unit off.  
Dimmer Operation  
During normal operation (when no alarm is sounding), press the Snooze/Dimmer Button to control the brightness of the  
LCD display.  
Using the iA63 in Other Countries  
Different regions of the world use different FM radio frequency steps and ranges. You will need to select the one that matches  
the standards in your region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is USA; if you live in the US,  
you may skip this section.  
1. Make sure the iA63 is OFF (not playing in any mode). Press and hold the  
“FM xxx” appears in the display. A beep will sound. Press the + or - Button to set the “xxx” to your region.  
2. Press the Button again (or no button within 10 seconds) to exit the radio frequency setting mode. 2 beeps will  
confirm the frequency has been set.  
Button for about 5 seconds until  
 
9
Troubleshooting  
Symptom  
Possible Problem  
Solution  
iA63 does not turn on  
AC adaptor isn't plugged into a working wall  
Plug the AC adaptor into a working wall socket and plug the connector  
socket or not plugged into the power supply jack into the supply jack on the unit  
on back of the unit  
iA63 doesn’t respond  
iA63 requires a reset  
If unit is plugged in and doesn't respond, try resetting the unit by  
following these steps:  
a) remove iPhone/iPod from dock  
b) unplug unit from power source  
c) remove back up batteries  
d) wait a few minutes, then resume use  
iPhone/iPod is not docked properly  
Remove your iPhone/iPod from the dock and check for obstruction on  
the connectors in the dock and on your iPhone/iPod. Then reseat it in the  
dock. Make sure that the stabilizer is properly positioned against the side  
of the iPhone/iPod, especially when rotating the dock to the landscape  
mode.  
Battery Low icon always Battery is weak  
flashing  
Replace with new battery  
Battery is not installed properly  
Check to make sure the polarity ( + and – ends) matches the diagram in  
the battery compartment (+ side up)  
iPhone/iPod does not iPhone/iPod is not docked properly  
respond to the unit/iPod  
Remove your iPhone/iPod from the dock and check for obstruction on  
the connectors in the dock and on your iPhone/iPod. Then reseat it in the  
dock.  
is playing but no sound  
comes out  
Your iPhone/iPod software is too old  
Upgrade software on your iPhone/iPod via iTunes on your computer  
iPhone/iPod is locked up/plays but no sound  
comes out  
Check the volume setting. Make sure your iPhone/iPod is working  
properly before docking into the unit. Please refer to your iPhone/iPod  
manual for details. See above for software upgrade information.  
You may need to reset your iPhone/iPod. Refer to your iPhone or  
iPod user guide for details on how to perform a reset.  
Using 1st or 2nd generation iPod, iPod Shuffle or  
other devices.  
iA63 cannot control those iPod models or other devices.  
iA63/iPhone/iPod  
performance is erratic  
The iA63 is reacting to external interference  
Move unit away from potential sources of external interference such as  
computers, modems, wireless devices (routers) or fluorescent light.  
No sound from iA63  
Volume is set too low on iA63  
Make sure volume is turned up  
iPhone/iPod didn’t  
charge up  
iPhone/iPod is not installed properly  
Remove your iPhone/iPod from the dock and check for obstruction on  
the connectors in the dock and on your iPhone/iPod. Then reseat it in  
the dock.  
iPhone/iPod is locked up/ frozen  
iPhone/iPod battery has problem  
Please make sure your iPhone/iPod is working properly before docking  
into the unit. Please refer to your iPhone/iPod manual for details.  
Time sync didn’t work  
Older iPod models such as iPod mini do not  
support time sync function  
Make sure you are using an iPhone or newer iPod such as touch, nano  
or classic. If not available, set time manually (see page 6).  
 
10  
Troubleshooting  
Symptom  
Possible Problem  
Solution  
Sound is distorted  
Volume level is set too high  
Decrease the volume  
Sound source is distorted  
If the iPhone/iPod original sound source (MP3) is old or of poor quality,  
distortion and noise are easily noticed with high-power speakers. Try a file  
from a trusted source such as iTunes.  
If you are using an external sound source like older generation of iPod or  
iPod shuffle, try reducing the output volume on the device itself. Also try  
turning bass boost OFF in your iPod settings.  
EQ settings on device are too high.  
This is normal  
Lower EQ settings on your iPhone/iPod.  
Unit/adaptor gets  
warm after extended  
play at high volume  
Turn unit off for awhile or lower volume  
Snooze time  
Custom snooze time not set  
Press and hold Snooze button then press + or - button to adjust  
is too long/short  
Alarm not working  
AM/PM time/alarm time not set correctly  
Alarm is not armed  
When setting clock or alarm time, take note of the PM indicator  
Make sure you see the alarm icon on the display (press alarm button)  
Download from Www.Somanuals.com11. All Manuals Search And Download.  
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,  
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully  
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in  
these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For  
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it  
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through  
the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions  
or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched  
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where  
it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning  
instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings  
or vents located on the product.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable  
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage  
to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A. the power supply cable or plug has been damaged.  
B. objects have fallen into or liquid has been spilled into the enclosure.  
C. the unit has been exposed to rain.  
D. the unit has been dropped or the enclosure damaged.  
E. the unit exhibits a marked change in performance or does not operate normally.  
12. Antenna – Do not connect an external antenna to the unit (other than that provided).  
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power  
cable should be unplugged from the unit to prevent damage or corrosion.  
14. Servicing – The user should not attempt to service the unit beyond those methods described in the users operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.  
 
12  
© 2011 SDI Technologies, Inc. All rights reserved  
iA63-012411-A  
Printed in China  
 

Graco Cell Phone M10E User Manual
Grizzly Ventilation Hood T10699 User Manual
Grizzly Welder G4179 User Manual
Grundig CRT Television LXW 70 8620 User Manual
Haier Refrigerator HYC 260 360 User Manual
Hamilton Beach Coffeemaker 48136 User Manual
Honeywell Network Card N ANN RLY User Manual
HP Hewlett Packard Tablet TC1100HP User Manual
Husqvarna Lawn Mower 532424695 User Manual
IBM Projector CP X445 User Manual