Hunter Fan Fan 90391 User Manual

Oscillating  
Stand Fan  
Owners Manual  
Model  
90391  
Form# 44830-01  
20100903  
©2010 Hunter Fan Co.  
 
InTroduCTIon  
Thank you for choosing the Hunter Oscillation Stand  
Fan. This manual gives you complete instructions for  
assembling and using your fan. Here are some the  
features you will enjoy with your fan:  
3 An attractive design that enhances any decor  
3 A powerful motor for maximum air flow  
3 Three speeds to adjust your comfort level  
3 Remote controlled for added convenience  
3 Multiple oscillation settings  
3 Timed running mode.  
3 Parts of this fan, including the blades and the grill,  
have been treated with Hunters dust Armor protection,  
making them less likely to attract dust and dirt.  
safeTy and WarnIngs  
REAd THIS EnTIRE MAnUAl CAREFUlly BEFORE  
BEgInnIng  
InSTAllATIOn.  
SAvE  
THESE  
InSTRUCTIOnS FOR REFEREnCE.  
To reduce the risk of fire or electrical shock, dO nOT use  
this fan with any solid-state speed control device.  
When using electrical appliances, basic precautions  
should always be taken to reduce the risk of fire, electric  
shock and personal injury:  
Read all instructions before using this fan.  
1. Improper installation may result in the risk of fire,  
electric shock or personal injury.  
2. To prevent the risk of fire and electric shock, dO  
nOT use the unit near windows. Rain and moisture  
may create an electrical hazard.  
3. The power plug must be removed from the power  
socket when not in use, before cleaning, servicing,  
maintenance and before moving to another location.  
4. This product is intended for indoor use only. dO  
nOT place fan in damp locations where humidity  
is present.  
©2010 Hunter Fan Co.  
3
44830-01 20100903  
 
 
5. The fan should be placed on a flat, stable surface or  
tabletop to avoid overturning.  
6. Use fan only for intended use, as described in this  
instruction manual.  
7. To protect against electrical shock, dO nOT immerse  
unit, plug or cord in water or spray with liquids.  
8. Close supervision is necessary when any appliance  
is used by or near children.  
9. nEvER insert fingers, pencils or any other objects  
through the grill when the fan is running.  
10. dO nOT operate any appliance with a damaged  
cord or plug, after the appliance malfunctions or has  
been dropped or damaged in any manner.  
11. To disconnect, grip plug and pull from wall outlet.  
nEvER pull on cord to disconnect from outlet.  
12. AlWAyS use on a dry surface.  
13. This product is intended for household use only and  
not for commercial or industrial use.  
14. dO nOT operate fan in the presence of explosive  
and/or flammable fumes.  
15. dO nOT place fan or any parts near an open flame,  
cooking or any other heating appliances.  
16. dO nOT use near curtains, plants, window  
treatments, etc.  
17. do not mix old and new batteries.  
18. do not mix alkaline, standard (carbon-zinc), or  
rechargables (ni-cad, ni-mh, etc) batteries  
19. This product conforms to Ul STd 507 and is certified  
to STd C22.2 no.113  
©2010 Hunter Fan Co.  
4
44830-01 20100903  
 
unpaCkIng  
As you unpack the fan, save the carton and packing  
materials in case you want to move or ship the unit in  
the future.  
Carefully remove all items from the box.  
nOTE: It is best to have someone hold the box while  
you lift the fan and the protective packaging out of the  
carton.  
(2) Nut  
Make sure all shipping materials are removed from fan  
before operating.  
figure 3.  
(3) Rear Grill  
fan assembly  
1. Remove the Plastic nut (2) from the fan motor  
housing . Figure 3.  
2. Set the Rear grill (3) against the front part of the  
Motor Housing with the handle facing up. The 3  
pins on the motor housing should stick through the  
back of the Rear grill. Figure 4.  
(2) Nut  
3. Screw the Plastic nut (2) onto the fan and tightenly  
firmly. Figure 4.  
figure 4.  
4. Remove the Plastic Sleeve from the motor housing  
(4) Fan Blade  
shaft and discard.  
5. Install the Fan Blade (4) by sliding it over the motor  
housing shaft, lining up the cut-outs on the back of  
the Blade with the Retaining Pins on the Motor shaft.  
Figure 5.  
6. Screw the Spinner (1) onto the shaft counterclockwise  
until secure. Figure 5.  
(1) Spinner  
7. Open the clips on the Front grill and remove the  
figure 5.  
grill screw from the outside of the rear grill (5) ring.  
(5) Front Guard  
8. Set the Front gill (5) into the notch on the bottom  
of the Rear grill (3) So the Hunter logo is facing  
rightside up. Figure 6.  
9. Close the clips On the Front grill to hold both grill  
pieces in place. Insert the grill screw on the top of  
the fan grill and tighten securely.  
figure 6.  
©2010 Hunter Fan Co.  
5
44830-01 20100903  
 
 
(7) Telescope Pole  
(8) Stand Base  
base assembly  
stand fan  
1. Slide the Telescope Rod (7) into the top of the Stand  
Base (8) aligning the 4 screw holes. Figure 7.  
2. Secure the Telescope Rod (7) by inserting the 4 base  
screws(9) inot the 4 nuts placed on the bottom of the  
fan base and tighten securely. Figure 8.  
3. Remove the Adjustment Knob(10) by twisting  
counter-clockwise and slide the Base Cover(11)  
down the Telescope Pole(7) until it covers the Screws  
at the Stand Base(8). Figure 9.  
figure 7.  
figure 8.  
figure 9.  
figure 10.  
(10) Adjustment  
Knob  
4. Reattach the Adjustment knob and tighten.  
5. loosen the Screw in the back of the Fan Assembly.  
(9) Screws  
6. Slide the Fan Assembly onto the telescope pole of the  
base until it rests on the top of the pole. Figure 10.  
7. tighten the screw on the back of the fan Assembly  
until secure.  
Warning: do not force pole into the Stand Base  
as damage to the Telescope Pole may occur. do not  
overtighten the Base nut or screws.  
(11) Base Cover  
Height adjustment  
1. grip the upper part of the telescope pole and loosen  
the Adjustment Knob.  
2. Raise or lower the pole to the desired height.  
3. Turn the Adjustment Knob until it is secure.  
©2010 Hunter Fan Co.  
6
44830-01 20100903  
 
 
remoTe baTTery InsTallaTIon  
1. Turn the Remote Control over and Remove the Battery  
Cover from the back by gently pressing down on the  
tab and sliding down on the tab. Figure 11.  
2. Insert2AAABatteriesintothebatterycompartment,  
ensuring the positive and negative ends of the  
batteries are installed correctly.  
3. Slide the Battery Cover back and snap into place.  
figure 11.  
operaTIon - fan/remoTe  
0.5H 1H 2H 4H  
See Figure 12. for fan operation and Figure 13. for  
remote operation.  
L
M
H
ON/SPEED - Turns the unit on and adjust the speed of  
ON l SPEED  
the unit between High, medium, and low.  
OSC  
OSC - Sets the oscillation mode of the fan.  
TIMER  
OFF  
Note: The fan can be turned to either side by grabbing  
the grill and turning left or right. A series of clicks  
will be heard as you turn the fan.  
figure 12.  
TIMER - Used to set the running time to 0.5 to 7.5 hours  
in 30 min, 0.5 increments.  
Note: The digital indicators on the fan will light up to  
indicate the timer setting. 0.5 will light up for 30  
minutes or 1H and 4H will light up to indicate 5  
hours.  
OFF - Turns the fan off.  
fan IndICaTors  
L M H - Indicates the current running speed of the fan.  
0.5 1H 2H 4H - Shows the number of hours the timer  
is set to run.  
- Fan oscillates from left to right.  
- Fan oscillates up and down.  
- Fan oscillates in a figure 8 motion.  
figure 13.  
©2010 Hunter Fan Co.  
7
44830-01 20100903  
 
 
maInTenanCe  
This fan is permanently lubricated and will not require  
additional lubrication (oil) for the life of the fan.  
This fan requires little maintenance and contains  
no user serviceable parts. dO nOT try to fix  
it yourself. Contact qualified service personnel  
if servicing is needed.  
Before cleaning, turn fan off and unplug from electrical  
outlet. Wipe off excess dust with a lintfree cloth.  
To ensure adequate air circulation to the motor, keep vents  
located at the rear of the motor housing free from dust  
accumulation. A vacuum cleaner hose can be used to  
clean these vents.  
dO nOT immerse the fan in water or any other liquid.  
ClEAnIng THE gRIll And BlAdE:  
1. Turn the fan off and unplug from the electrical outlet.  
2. disassemble the grills by carefully lifting the latches  
around the outer ring.  
3. Remove the front grill.  
4. The blade may be removed by turning the Spinner  
Knob clockwise.  
3 Use a dry or slightly damp lint free cloth to clean  
the fan. do not use a furniture polish or any other  
cleaners that leave any residue, as they will damage  
the protective dust Armor.  
3 dO nOT allow water or any other liquid to get into  
the motor housing or base.  
3 Reassemble the fan after blades and grills have dried  
completely.  
3 dO nOT plug the fan into an electrical outlet until it  
has been fully reassembled.  
©2010 Hunter Fan Co.  
8
44830-01 20100903  
 
 
1. Problem  
3 Fan will not oscillate.  
Solution  
3 Push down on the knob on top of motor housing to  
activate oscillation.  
2. Problem  
3 Can not adjust the angle of the fan.  
Solution  
3 gentle grasp the grill of the fan and tilt up or down.  
3. Problem  
3 Remote control will not operate.  
Solution  
3 Remove the battery cover and confirm the batteries  
are installed correctly according to polarity markings.  
TeCHnICal supporT  
If you have any additional questions or problems with  
your Hunter Portable Fan, please call:  
USA: 1-888-830-1326  
Canada: 1-866-268-1936  
Hours of operation are from 7:00 am to 7:00 pm  
Monday - Friday and 8:00 am to 5:00 pm on Saturday,  
Central Time. you may also contact us over the Internet at  
WarranTy  
The Hunter Fan Company makes the following limited  
warranty to the user or consumer purchaser of this Hunter  
Portable fan:  
If your Hunter Portable Fan motor fails at any time within  
one year after the date of sale to you due to a defect in  
material or workmanship, labor to repair the defect will  
be provided free of charge at our nearest service center  
or our Service department in Memphis, Tennessee. you  
will be responsible for labor costs after this one-year  
period. The foregoing limited warranty applies only to  
the motor itself, and does not apply to electronic controls  
©2010 Hunter Fan Co.  
9
 
 
such as remote controls, remote control receivers or  
transmitters used in conjunction with the motor. These  
electronic control items are included in the one year  
limited warranty below.  
If any part of your Hunter Portable Fan other than the  
motor fails at any time with one year after the date of  
sale to you due to a defect in material or workmanship,  
we will repair or, at our option, replace the defective  
part free of charge for parts and labor performed at our  
nearest service center or at our Service department in  
Memphis, Tennessee.  
IF THE USER OR COnSUMER PURCHASER CEASES TO  
OWn THE FAn, THIS WARRAnTy And Any IMPlIEd  
WARRAnTy WHICH THEn REMAInS In EFFECT,  
InClUdIng BUT nOT lIMITEd TO Any IMPlIEd  
WARRAnTy OF MERCHAnTABIlITy OR FITnESS FOR A  
PARTICUlAR PURPOSE, ARE vOIdEd. nO WARRAnTy,  
EXPRESSEd OR IMPlIEd, InClUdIng Any WARRAnTy  
OF MERCHAnTABIlITy OR FITnESS FOR A PARTICUlAR  
PURPOSE, IS MAdE In RESPECT TO THE glASS glOBES  
OR lIgHT BUlBS OR THE FInISH On Any METAl  
PORTIOn OF THE FAn. THIS WARRAnTy IS In lIEU  
OF All OTHER EXPRESS WARRAnTIES. THE dURATIOn  
OF Any IMPlIEd WARRAnTy, InClUdIng, BUT  
nOT lIMITEd TO Any IMPlIEd WARRAnTy OF  
MERCHAnTABIlITy OR FITnESS FOR A PARTICUlAR  
PURPOSE, In RESPECT TO Any HUnTER FAn MOTOR  
OR OTHER FAn PART, IS EXPRESSly lIMITEd TO THE  
PERIOd OF THE EXPRESS WARRAnTy SET FORTH  
ABOvE FOR SUCH MOTORS And OTHER PARTS.  
This warranty is voided if your Hunter Fan is not  
purchased and used in the USA.  
This warranty excludes and does not cover defects,  
malfunctions or failures of any Hunter Portable fan  
which were caused by repairs by persons not authorized  
by us, use of parts or accessories not authorized by  
us, mishandling, improper installation, modifications,  
or damage to the Hunter Portable fan while in your  
possession, or unreasonable use, including failure to  
provide reasonable and necessary maintenance.  
To obtain servicing, contact the nearest Hunter authorized  
service center or the Hunter Fan Company Service  
department, 7130 goodlett Farms Pkwy. Suite 400,  
©2010 Hunter Fan Co.  
10  
44830-01 20100903  
 
Memphis, Tennessee 38016. Please contact us before  
shipping your fan to us. If we authorize you to ship it to  
us, you will be responsible for all insurance and freight  
or other transportation charges to our factory service  
center. We will return your Hunter Fan freight prepaid.  
your portable fan should be properly packed to avoid  
damage in transit since we will not be responsible for  
any such damage. Proof of purchase is required when  
requesting warranty service. The purchaser must present  
sales receipt or other document that establishes proof of  
purchase.  
In nO EvEnT SHAll HUnTER FAn COMPAny BE  
lIABlE FOR COnSEQUEnTIAl OR InCIdEnTAl  
dAMAgES.  
SOME STATES dO nOT AllOW lIMITATIOnS On  
HOW lOng An IMPlIEd WARRAnTy lASTS OR  
THE EXClUSIOn OR lIMITATIOn OF InCIdEnTAl  
OR COnSEQUEnTIAl dAMAgES SO THE ABOvE  
lIMITATIOn MAy nOT APPly TO yOU.  
THE WARRAnTy gIvES yOU SPECIFIC lEgAl RIgHTS  
And yOU MAy AlSO HAvE OTHER RIgHTS WHICH  
vARy FROM STATE TO STATE.  
produCTs  
Company  
7130 goodlett Farms Pkwy., Suite 400  
Memphis, Tennessee 38016  
To learn more about Hunter  
Fan Company products,  
please see our Web page at:  
www.hunterfan.com  
Printed in china and Taiwan  
©2010 Hunter Fan Co.  
11  
44830-01 20100903  
 
 

Graco High Chair 3170 User Manual
Grindmaster Coffeemaker 73010 User Manual
Hamilton Beach Toaster 24669 User Manual
HANNspree Flat Panel Television MAK 000019 User Manual
Heath Zenith Home Safety Product 5212 User Manual
Honeywell Gas Heater VS820 User Manual
HP Hewlett Packard Computer Monitor 3535437 User Manual
Hubbell Switch C5027 User Manual
Impex Home Gym TC 3500 User Manual
Impex Tent MS 93 User Manual