Matrix® 47 Operations Manual
531338-1_C
Table of Contents
How Sonar Works
1
3D Sonar............................................................................................................................................................ 2
2D Sonar............................................................................................................................................................ 2
What’s On the Display (3D View)
What’s On the Display (2D View)
Views
3
5
7
3D Sonar View ................................................................................................................................................ 7
3D/2D Sonar Combo View ........................................................................................................................ 9
6-Beam Sonar View .................................................................................................................................... 10
2D Sonar View................................................................................................................................................ 11
Real Time Sonar (RTS™) Window............................................................................................................ 12
2D Zoom View .............................................................................................................................................. 13
2D Big Digits View ...................................................................................................................................... 14
Bottom Presentation .................................................................................................................................. 15
Key Functions
17
POWER/LIGHT Key ...................................................................................................................................... 17
VIEW Key ........................................................................................................................................................ 17
MENU Key ...................................................................................................................................................... 17
4-WAY Cursor Control Key ........................................................................................................................ 18
EXIT Key .......................................................................................................................................................... 18
Accessory Bus
19
19
20
22
Powering Up the Unit
The Menu System
Start-Up Options Menu
Normal Operation........................................................................................................................................ 22
Simulator ...................................................................................................................................................... 23
System Status .............................................................................................................................................. 23
PC Connect (with PC Connect Cable Only) .......................................................................................... 24
ii
Table of Contents
Sonar X-Press™ Menu
25
3D Bottom Zoom (3D Sonar, 3D/2D Sonar Combo Views Only) .............................................. 26
3D Lower Range (3D Sonar, 3D/2D Sonar Combo, 6-Beam Sonar Views Only) ...................... 26
3D History (3D Sonar, 3D/2D Sonar Combo Views Only) ............................................................ 27
2D Sonar Window (3D/2D Sonar Combo View Only).................................................................... 27
Reset View (3D Sonar, 3D/2D Sonar Combo Views Only)............................................................ 27
6-Beam Sensitivity (6-Beam Sonar View Only) .................................................................................. 28
Sensitivity (2D Sonar, 2D Zoom, 2D Big Digits Views Only) ........................................................ 28
Upper Range (Advanced: 2D Sonar, 2D Big Digits Views Only) ................................................ 29
Lower Range (2D Sonar, 2D Zoom, 2D Big Digits Views Only) .................................................. 30
Chart Speed (2D Sonar, 2D Zoom, 2D Big Digits Views Only) .................................................... 31
Bottom View (2D Sonar, 2D Zoom, 2D Big Digits Views Only) .................................................. 31
Zoom Level (2D Zoom View Only) ........................................................................................................ 32
Sonar Menu Tab
33
3D Bottom Style .......................................................................................................................................... 34
3D Frame Style ............................................................................................................................................ 34
Beam Select .................................................................................................................................................. 34
Fish ID+™ ........................................................................................................................................................ 35
Fish Sensitivity.............................................................................................................................................. 36
Fish ID 3D Reference .................................................................................................................................. 36
Real Time Sonar (RTS™) Window .......................................................................................................... 37
Depth Lines (Advanced) ............................................................................................................................ 38
Surface Clutter (Advanced) ...................................................................................................................... 39
Noise Filter (Advanced) ............................................................................................................................ 39
Max Depth (Advanced) ............................................................................................................................ 40
Water Type (Advanced) ............................................................................................................................ 40
Alarms Menu Tab
41
Depth Alarm.................................................................................................................................................. 42
Fish ID Alarm ................................................................................................................................................ 42
Low Battery Alarm ...................................................................................................................................... 43
Alarm Tone .................................................................................................................................................... 43
iii
Table of Contents
Setup Menu Tab
44
Units - Depth ................................................................................................................................................ 45
Units - Temp (International Only) ........................................................................................................ 45
Units - Distance (with Temp/Speed or GPS Receiver) .................................................................... 45
Units - Speed (with Temp/Speed or GPS Receiver) ........................................................................ 46
User Mode...................................................................................................................................................... 46
Language (International Only) .............................................................................................................. 46
Triplog Reset (with Temp/Speed or GPS Receiver).......................................................................... 47
Restore Defaults .......................................................................................................................................... 47
Select Readouts (Advanced: 3D and 2D Sonar Views Only)........................................................ 48
Depth Offset (Advanced).......................................................................................................................... 50
Temp Offset (Advanced) .......................................................................................................................... 50
Speed Calibration (Advanced: with Temp/Speed Only) .............................................................. 50
NMEA Output (Advanced) ........................................................................................................................ 51
Views Menu Tab
52
53
54
Accessories Menu Tab
Troubleshooting
Matrix® Doesn’t Power Up ...................................................................................................................... 54
Matrix® Defaults to Simulator with a Transducer Attached ...................................................... 54
Display Problems.......................................................................................................................................... 55
Finding the Cause of Noise ...................................................................................................................... 56
Matrix® Fishing System Accessories
Specifications
57
58
59
Contact Humminbird®
NOTE: Entries in this Table of Contents which list (International Only) are only available on products
sold outside of the US and Canada by our authorized International Distributors. To obtain a list of
our Customer Resource Center at 1-800-633-1468 to locate the distributor nearest you.
NOTE: Entries in this Table of Contents which list (with PC Connect Cable Only) require the purchase of
or contact our Customer Resource Center at 1-800-633-1468.
iv
How Sonar Works
Sonar uses sound waves to determine the presence and location of underwater objects. The
time measured between the transmission of the sound wave and the reception of any
reflection can be used to determine distance from an object. Analysis of the reflected signal
can also be used to determine location, size, or composition of underwater objects.
Humminbird® products consist of two main components: the sonar unit and the
transducer. The sonar unit contains the transmitter and receiver, as well as the user
controls and LCD display. The transducer is mounted beneath the water surface and
converts electrical energy from the transmitter into mechanical pulses or sound waves. The
transducer also receives reflected sound waves and converts them back into electrical
signals for display on the sonar unit.
The transmit and receive cycle is very fast. A sound wave can travel from the surface to a
depth of 240 ft (70 m) and back again in less than ¹⁄₄ of a second. It is unlikely that your boat
can "outrun" this sonar signal.
A number of variables affect the nature of information which can be derived from the sonar
return. Sonar signals generated at a higher frequency have the advantage of greatly increased
sonar resolution, although the distance (depth) a high-frequency signal can travel is relatively
short. A low frequency signal can travel great distances, but provides poor sonar resolution. The
shape of the transmitted sonar signal greatly affects the information available as well. A single
wide beam has a large area of coverage but poor resolution of detail. A narrow beam has
excellent detail, but only a limited area of coverage.
1
3D Sonar
Your Matrix® Fishing System uses a six-element transducer that
transmits at 455 kHz and is capable of reaching depths of 240 ft
(75 m). Each transmitted beam is 16 degrees in width and is
symmetrical. The six beams are lined up next to each other to
provide a total coverage of 53 degrees from side to side, and 16
degrees from front to back. Using multiple narrow beams together
gives you a wide area of coverage for terrain interpretation and fish
location, without sacrificing the detail only a narrow beam can
provide. Your Matrix® Fishing System gathers information from a
continuous series of these returned signals. It then interprets this
information to create a detailed 3-dimensional view of the terrain
passing beneath your boat as you travel across the water.
2D Sonar
Your Matrix® Fishing System also has the capability of displaying
traditional 2-dimensional sonar information from either a 455 kHz
beam or an 83 kHz beam. The 455 kHz single beam has the
advantage of providing increased sonar resolution but is limited to
a depth capability of 240 ft (75 m). The 83 kHz single beam sonar
has the advantage of providing sonar information to 1000 ft
(330 m) but the sonar resolution is not as great as with the 455 kHz
single beam.
NOTE: Depth capability is affected by such factors as boat speed, wave
action, bottom hardness, water conditions and transducer installation.
2
What’s On the Display (3D View)
In 3D views, your Matrix® Fishing System can display a variety of useful information about
Depth - water depth; can be set to alarm
when the water becomes too shallow.
Temperature - water surface temperature.
Bottom Contour - Shows the shape of the
bottom derived from depth measurements
on 6 beams. 3 bottom styles are available; the
front edges of the bottom contour are
outlined to create a visual anchor. The width
of the bottom covered is approximately equal
to the depth.
Timer - elapsed time with Temp/Speed
Accessory or GPS Receiver.
Distance - distance traveled with Temp/Speed
Accessory or GPS Receiver.
Average Speed - average speed reading with
Temp/Speed Accessory or GPS Receiver.
Speed - if a Temp/Speed accessory or GPS Receiver is attached, the Matrix can display the speed
of the boat, and can keep a Triplog of nautical or statute miles traveled.
NOTE: Entries in this view that list (with Temp/Speed or GPS Receiver) are available if either device is
the GPS receiver will be displayed on the view.
3
the area under and adjacent to your boat, including the following items:
Boat/Direction Arrow - A simple, solid 3D
boat is drawn when the Upper Depth Range is
0. A solid 3D arrow is drawn when the Upper
Depth Range is not 0.
Fish ID+™ - A fish icon will be shown at the
derived position of the fish. Six fish icon styles
will be used to indicate the primary beam in
which the fish was found. Left-facing fish
indicate fish off the port side of the boat,
while right-facing fish indicate fish off the
starboard side. Each fish icon is available in
three different sizes. Larger fish icons are
used to represent stronger returns. The icons
used in the 2D Sonar View are identical to the
icons used in the 3D Sonar View.
Upper and Lower Depth Range Labels
Battery Voltage - the voltage of the
boat’s battery; can be set to alarm if the
voltage falls below a certain point.
Frame - provides a reference for bottom and
Fish ID information. A Range of frame styles
are available, from simple to complex.
connected to the Matrix® Fishing System. If both devices are connected, then only the information from
4
What’s On the Display (2D View)
In 2D views, your Matrix® Fishing System can display a variety of useful information
Depth - water depth; can be set to alarm
Cursor - available in Freeze Frame and can
when the water becomes too shallow.
depth of a sonar return and bottom depth
Speed - if a Temp/Speed accessory or GPS
Receiver is attached, the Matrix can display
the speed of the boat, and can keep a Triplog
of nautical or statute miles traveled.
Temperature - water surface temperature.
Bait Ball
Timer - elapsed time with Temp/Speed
Accessory or GPS Receiver.
Distance - distance traveled with Temp/Speed
Accessory or GPS Receiver.
Average Speed - average speed reading with
Temp/Speed Accessory or GPS Receiver.
Hard Bottom
Rocky Bottom
Second Sonar Return - when the sonar
signal bounces between the bottom and the
surface of the water and back again. Use the
appearance of the second return to determine
bottom hardness. Hard bottoms will show a
strong second return, while soft bottoms will
show a very weak one or none at all.
Cursor Dialog Box - indicates cursor depth
directly below the cursor.
NOTE: Entries in this view that list (with Temp/Speed or GPS Receiver) are available if either device is
the GPS receiver will be displayed on the view.
5
about the area under and adjacent to your boat, including the following items:
be positioned in the Sonar View to provide
below the cursor.
Structure - where fish may be hiding.
Thermoclines - layers of water with different
temperatures that appear at different depths
and different times of the year. A thermocline
typically appears as a continuous band of
many gray levels moving across the display at
the same depth.
Fish ID+™ - A fish icon will be shown at the
derived position of the fish. Six fish icon styles
will be used to indicate the primary beam in
which the fish was found. Left-facing fish
indicate fish off the port side of the boat, while
right-facing fish indicate fish off the starboard
side. Each fish icon is available in three
different sizes. Larger fish icons are used to
represent stronger returns. The icons used in
the 2D Sonar View are identical to the icons
used in the 3D Sonar View.
Soft Bottom
RTS™ (Real Time Sonar) Window
Battery Voltage - the voltage of the boat’s
battery; can be set to alarm if the voltage falls
below a certain point.
on the display and the depth of the bottom
connected to the Matrix® Fishing System. If both devices are connected, then only the information from
6
Views
The views available on your Matrix® Fishing System are:
• 3D Sonar View
• 3D/2D Sonar Combo View
• 6-Beam Sonar View
• 2D Sonar View
• 2D Zoom View
• 2D Big Digits View.
3D Sonar View is the default view. When the VIEW key is pressed, the display cycles through
the available views. When the EXIT key is pressed, the display cycles through the available
views in reverse order. Any view can be hidden or displayed as part of the view rotation using
the Views Menu tab.
NOTE: When you change any menu settings that affect the sonar, the view will update immediately
(i.e. you don’t have to exit the menu to apply the change to the screen). For instance, by switching
between "Inverse" and "Structure ID®" from the X-Press™ Menu it is possible to quickly alternate
between the two viewing methods.
NOTE: If the Depth number is flashing, it means that the unit is having trouble locating the bottom.
This usually happens if the water is too deep, the transducer is out of the water, the boat is moving
too fast, or for any other reason that the unit can’t accurately receive continuous data.
3D Sonar View
3D Sonar View displays a 3-dimensional representation of the bottom. Depth is always
displayed in the upper left hand corner. Temperature and speed are displayed if the
temp/speed paddle wheel is connected or if a GPS receiver is connected. The sonar returns
from each of the six elements are combined to create a 3-dimensional wire-frame
representation of the bottom. The graphic depiction of the bottom provides you with an
effective tool for understanding the terrain beneath the boat. The boat symbol represents
the location of your boat in relation to the on-screen information.
The most recent sonar returns are charted on the upper right side of the screen and move to
the lower left as new information is received. The width of coverage is approximately equal
to the depth. Depth range is automatically selected to keep the bottom visible on the display.
In some situations, the selected point of view may prevent the display of some information
due to the slope of the terrain. An option is available to change the perspective, or viewpoint,
7
in order to let you see information that would otherwise be masked by the terrain. Use the
4-WAY Cursor Control key to change the perspective. The perspective can be re-set to the
default view by selecting Reset View from the X-Press™ menu.
If a return meets certain criteria one of 18 kinds of fish symbols will be assigned. There are
three different size fish symbols to indicate the intensity of the return and each of the six
beams has a unique set of fish symbols (see Fish ID+™ on the Main Menu Sonar Tab for more
information).
Six additional Digital Readouts display information from optional-purchase accessories.
These information boxes can be customized to show only the information desired (see
Setup Menu Tab, Select Readouts).
3D Sonar View
Boat Icon
Depth
Temperature
Upper
Depth Range
3D Reference
Frame
Depth
Fish ID+™
Symbols
Triplog with
Timer,
Distance
Travelled
and Average
Speed
3D Bottom
Contour
Lower
Depth Range
Speed
Voltage
8
3D/2D Sonar Combo View
3D/2D Sonar Combo View displays a 3-dimensional representation of the bottom next to the
traditional 2-dimensional sonar representation. Depth is always displayed in the upper left
hand corner. The 3D/2D Sonar Combo View is especially useful for evaluating the bottom
terrain from the 3D window while simultaneously viewing the 2D window for structure and
bottom hardness. Refer to the 3D Sonar View and the 2D Sonar View sections for more
information on these views.
The digital readouts in the 3D/2D Sonar Combo View cannot be customized, making
information such as water temperature and voltage unavailable in this view.
3D/2D Sonar Combo View
Upper
Depth Range
Depth
2D Sonar
Window
Lower
Depth Range
3D Sonar
Window
9
6-Beam Sonar View
6-Beam Sonar View displays information from each of the six 455 kHz beams in a traditional
2D representation. This view displays the raw sonar returns from each of the beams that are
used to create the 3-dimensional wire frame representation of the bottom in the 3D Sonar
View. The 6-Beam Sonar View can be used for identifying structure on the bottom and sonar
returns in the water column. The 6-Beam Sonar View also provides information on sonar
targets relative to the boat. The far right window displays sonar targets which are to the far
right of the boat and the far left window displays sonar targets which are to the far left of
the boat. The remaining windows display sonar targets which are successively closer to the
boat. The width of coverage is approximately equal to the current depth.
6-Beam Sonar View
Upper
Depth Range
Depth
Boat Icon
6 Beam
Sonar History
Lower
Depth Range
The digital readouts in the 6-Beam Sonar View cannot be customized, making information
such as water temperature and voltage unavailable in this view.
10
2D Sonar View
2D Sonar View is a 2-dimensional view that presents a historical log of sonar returns. Depth is
always displayed. Readouts for temperature and speed are automatically displayed if the
appropriate accessory is connected. The most recent sonar returns are charted on the right side
of the window; as new information is received, the older information is moved across the
display to the left. A Digital Depth Readout is displayed in the upper left corner. A scale with
Upper and Lower Depth Range readouts appears along the right edge of the Sonar View. The
scale indicates the distance from the surface of the water to a depth range sufficient to show
the bottom. Depth Range is automatically selected to keep the bottom visible on the display,
although you can adjust it manually as well (see Sonar X-Press™ Menu). Six additional Digital
Readouts display information from optional-purchase accessories. These information boxes can
be customized to show only the information desired (see Setup Menu Tab, Select Readouts).
When in 2D Sonar View, your unit operates like a typical depthsounder. There are, however,
several exceptions. The six-beam 53 degree transducer allows you to search for fish with a
much wider area of coverage. Only the two center beams provide sonar returns for the
bottom contour shown on the display. The fish symbols shown in the 2D Sonar View are the
same as those used in the 3D Sonar View providing information on the location of the fish
relative to the boat (see Sonar Menu Tab, Fish ID+). Use the 2D Sonar View for identifying
structure and bottom hardness.
2D Sonar View
Upper Depth
Range
Depth
Speed
RTS™ Window
Temperature
Triplog
Cursor
Sonar History
Window
Voltage
Lower Depth
Range
Cursor Dialog Box
Freeze Frame - Pressing any arrow on the 4-WAY Cursor Control key will freeze the screen in
the 2D Sonar View and a cursor will be displayed on the screen. The cursor can be positioned
on the display using the 4-WAY Cursor Control key to determine the depth of any sonar
return. The RTS™ Window continues to update in Freeze Frame. In addition, see the effects
of menu setting changes with Instant Image Update. Pressing EXIT will exit Freeze Frame
and the display will start to scroll. Freeze Frame is only available in the 2D Sonar View.
11
Real Time Sonar (RTS™) Window
A Real Time Sonar (RTS™) Window appears on the right side of the display in the
2D Sonar View only. The RTS™ Window always updates at the fastest rate possible for depth
conditions and shows only the returns from the bottom, structure and fish that are within
the transducer beam. The RTS™ Window plots the depth and intensity of a sonar return (see
Sonar Menu - RTS™ Window).
The Narrow RTS™ Window
indicates the sonar intensity
through the use of grayscale.
The grayscale used matches
the bottom view grayscale
setting used in the sonar
history window (i.e. Inverse,
StructureID®, WhiteLine™,
Bottom Black). The depth of
the sonar return is indicated
by the vertical placement of
the return on the display
depth scale.
The Wide RTS™ Window
indicates the sonar intensity
through the use of a bar
graph. The length of the
plotted return provides an
indication of whether the
return is weak or strong. The
depth of the sonar return is
indicated by the vertical
placement of the return on
the display depth scale. The
Wide RTS™ Window does not
make use of grayscale.
12
2D Zoom View
2D Zoom View increases the displayed resolution to separate sonar returns that are very
close together, such as those caused by fish suspended close to the bottom or within
structure. Digital depth is displayed in the upper left hand corner. In 2D Zoom View, the
display is split to show a narrow slice of the full range view on the right and the zoomed view
on the left. The full range view on the right also contains the Zoom Preview Box that shows
what part of the full range view is shown in zoomed view on the left; the Zoom Preview Box
tracks the bottom in the full range view.
As the depth changes, the zoomed view updates automatically to display a magnified image
of the bottom. The Zoom Preview Box shows where the zoomed view is in relation to the full
range view. The Zoom Level, or magnification, is displayed in the lower left corner and can
be changed to suit conditions (see Sonar X-Press™ Menu: Zoom Level). Upper and Lower
Zoom Depth Range numbers indicate the depth of the water you are viewing.
The digital readouts in the 2D Zoom View cannot be customized, making information such
as water temperature and voltage unavailable in this view.
2D Zoom View
Upper Depth
Range,
Full Range View
Depth
Upper Depth
Range, Zoom View
Full Range View
Zoom
Preview Box
Zoomed
View
Lower Depth
Range,
Full Range View
Zoom
Level
Lower Depth
Range, Zoom View
13
2D Big Digits View
2D Big Digits View provides digital data in a large, easy-to-see format. Depth is always
displayed. Readouts for temperature, speed and Triplog information are displayed
automatically if the appropriate accessory is connected to the system. The Triplog shows
distance traveled, average speed, and time elapsed since the Triplog was last reset. The
digital readouts in the 2D Big Digits View cannot be customized.
2D Big Digits View
Timer shows the time
elapsed since Triplog
was last reset
Depth
Distance is the distance
traveled since the
Triplog was last reset
Temperature
Voltage - the battery
voltage.
Average Speed shows
the speed since the
Speed
Triplog was last reset
14
Bottom Presentation
As the boat moves, your Matrix® Fishing System charts the changes in depth on the display
to create a profile of the Bottom Contour. The type of bottom can be determined from the
return charted on the display. A Hard Bottom such as compacted sediment or flat rock
appears as a thinner line across the display. A Soft Bottom such as mud or sand appears as a
thicker line across the display. Rocky Bottoms have a broken, random appearance.
Bottom Contour Profile with RTS™ Window.
Temp/Speed Accessory is optional.
Hard Bottom
Soft Bottom
Rocky Bottom
The sonar returns from the bottom, structure and fish can be represented as either Inverse
(default), WhiteLine™, Structure ID®, or Bottom Black. See Sonar X-Press™ Menu: Bottom
View for details on how to set the bottom view.
15
Inverse is a method where weak returns are shown with dark
pixels and strong returns with lighter pixels. This has the
benefit of ensuring that weak signals will be clearly visible on
the display.
Structure ID® represents weak returns as light pixels and
strong returns as dark pixels. This has the benefit of
ensuring that strong returns will be clearly visible on the
display.
WhiteLine™ highlights the strongest sonar returns in white,
resulting in a distinctive outline. This has the benefit of
clearly defining the bottom on the display.
Bottom Black displays all pixels below the bottom contour as
black, regardless of signal strength. This has the benefit of
providing a high contrast between the bottom and other
sonar returns on the display. Any targets such as fish,
structure and thermoclines will be shown using the
Structure ID® method.
16
Key Functions
Your Matrix® Fishing System user interface consists of a set of easy-to-use keys that work
with various on-screen views and menus to give you flexibility and control over your
fishing experience.
POWER/LIGHT Key
The POWER/LIGHT key is used to turn the Matrix® Fishing System on and
off, and also to adjust the backlight and contrast of the display. Press the
POWER/LIGHT key to turn the unit on. The Title screen is then displayed until the Fishing
System begins sonar operation.
Your Fishing System will start up with the backlight on and will
automatically turn it off to conserve power. To turn the backlight on
for night fishing, or to adjust the display contrast, press the
POWER/LIGHT key to access the Light and Contrast menu. Use the
4-WAY Cursor key to select Light or Contrast and then use the LEFT or RIGHT Cursor key to
change the settings. Press EXIT to exit the Light and Contrast menu.
Press and hold the POWER/LIGHT key for 3 seconds to turn the unit off. A message will
appear telling you how many seconds there are until shutdown occurs. Your Fishing System
should always be turned off using the POWER/LIGHT key. This will ensure that shutdown
occurs properly and any menu settings will be saved.
VIEW Key
The VIEW key is used to cycle through all available views. Press the VIEW key
to advance to the next view. Repeatedly pressing VIEW cycles through all
views available. Views can be hidden to optimize the system to your fishing
requirements (see Views Menu Tab).
MENU Key
The MENU key is used to access the menu system.
Start-Up Options Menu - Press the MENU key during the power up sequence to view the
Start-Up Options menu.
17
X-Press™ Menu - Press the MENU key once for the Sonar X-Press™ Menu. The X-Press™ Menu
allows you to access frequently-used settings without having to navigate through the whole
menu system. When the X-Press™ Menu is displayed, you can use the UP or DOWN Cursor
keys to move to a particular menu choice. As soon as you alter a parameter (using the RIGHT
or LEFT Cursor keys) the X-Press™ Menu will collapse temporarily, and the screen will update
if it is affected by your menu setting change, allowing you to see the effects of your action
immediately. Reactivate the X-Press™ Menu by using the UP or DOWN Cursor keys.
Main Menu - Press the MENU key twice for the tabbed Main Menu System. The Main Menu
System is organized under tabbed headings to help you find a specific menu item quickly:
Alarms, Sonar, Setup, Views, and Accessories tabs are part of your tabbed Main Menu
System. Use the LEFT or RIGHT 4-WAY Cursor Control key to select a tab; then use the DOWN
or UP key to select the menu item, and the LEFT or RIGHT key to alter a menu setting.
4-WAY Cursor Control Key
The 4-WAY Cursor Control key has multiple functions, depending on the
situation:
•
•
•
Use the DOWN or UP arrow keys to select a menu choice from the menu list,
Use the LEFT or RIGHT arrow keys to change a menu setting.
Press any arrow key to activate Freeze Frame while in the 2D Sonar View and then
use the 4-WAY Cursor Control key to position the cursor on the display.
•
Press any arrow key to change the perspective in the 3D Sonar View. Subsequent
presses of the 4-WAY Cursor Control key rotate and tilt the 3D representation.
NOTE: Menu choices are implemented and saved immediately - no further action is required.
EXIT Key
The EXIT key has multiple functions, depending on the situation:
•
•
If an alarm is sounding, pressing EXIT will cancel the alarm.
If a menu tab is selected, pressing EXIT will exit the menu mode and return to the
view.
•
If a menu is active, pressing EXIT will return to the previous level in the menu
system.
•
•
Pressing EXIT will cycle through the available views in reverse order.
If Freeze Frame is active, pressing EXIT will return to a scrolling display.
18
Accessory Bus
Use the Accessory Bus to expand the functionality of the
Matrix® Fishing System. Accessories plug directly into
the Matrix® Fishing System, enabling Advanced
features such as WeatherSense®, GPS Functionality and
the SmartCast® Wireless Sonar Link. Additional menu
tabs and menu choices will be added to the menu
system automatically when an accessory is plugged into
the unit. In addition, multiple accessories can be
attached simultaneously. See Accessories Menu Tab and
Matrix® Fishing System Accessories in this manual, as
well as your accessory's Operations Manual for
additional details.
NOTE: Accessories to enable WeatherSense®, GPS
Functionality and the SmartCast® Wireless Sonar Link
require separate purchases. You can visit our website at
www.humminbird.com or contact our Customer Resource
Center at 1-800-633-1468 for additional details.
Powering Up the Unit
Turn on your Matrix® Fishing System by pressing the
POWER/LIGHT key. The Title screen is displayed until
the Fishing System begins operation. Your Fishing
System will begin Normal or Simulator operation,
depending on the presence or absence of a transducer.
Matrix 47 3D Title Screen
19
The Menu System
The menu system is divided into easy-to-use menu modules. The main components of the
menu system are:
Start-Up Options Menu - Press the MENU key during the power up sequence to view the
Start-Up Options menu.
X-Press™ Menu - The X-Press™ Menu allows you to access
the settings that are changed frequently without having to
navigate through the whole menu system. Press the MENU
key once to display the X-Press™ Menu. When you select a
menu item from the X-Press™ Menu, the menu will collapse,
leaving only the menu choice on the screen. Use the UP or
DOWN Cursor keys to reactivate the X-Press™ Menu.
NOTE: The X-Press™ Menu choices will vary depending on which
view is active when you press the MENU key, as well as whether you
X-PressTM Menu
are in Normal or Advanced User Mode.
Main Menu Tabs - Less frequently-adjusted menus are
grouped into the Main Menu System. The Main Menu
system is organized under the following tab headings to
help you find a specific menu item quickly: Alarms, Sonar,
Setup, Views, and Accessories.
Press the MENU key twice for the Main Menu, then use the
4-WAY Cursor LEFT or RIGHT key to select a tab, and use the
DOWN or UP key to select a specific menu item under that
tab, then use the LEFT or RIGHT keys again to change a menu
setting. Press the EXIT key to move quickly to the top of the
tab. A down arrow at the bottom of a menu means that you
can scroll to additional menu choices using the DOWN
Cursor key. A right or left arrow on a menu choice means that
you can use the RIGHT or LEFT Cursor keys to make changes
Main Menu System
Normal User Mode
or see more information.
NOTE: The Main Menu choices will vary depending on whether
you are in Normal or Advanced User Mode.
20
User Mode (Normal or Advanced) - An Advanced Mode is provided for users who desire the
highest level of control over the Fishing System and Normal Mode for users who desire
greater simplicity and fewer menu choices. While you are in Advanced Mode, additional
Advanced menu choices will be displayed throughout the menu system when you navigate
to specific menus. Any changes made while in Advanced Mode will remain in effect after you
switch back to Normal Mode. See Setup Menu Tab: User Mode for specific instructions on
changing to Advanced User Mode.
Sonar Tab, Normal Mode
Sonar Tab, Advanced Mode
Total Screen Update™ - when you change any menu settings that affect the Sonar View, the
view will update immediately (i.e. you don’t have to exit the menu to apply the change to
the screen). For instance, by switching between "Inverse" and "Structure ID®" from the
X-Press™ Menu it is possible to alternate quickly between the two viewing methods.
21
Start-Up Options Menu
Press the MENU key when the Title screen is displayed to access the Start-Up Options
menu.
Use the UP or DOWN 4-WAY Cursor Control keys to
position the cursor, then the RIGHT Cursor key to select
one of the following choices. If you wait too long, the
system will default to whichever menu mode happens
to be highlighted:
• Normal
• Simulator
• System Status
• PC Connect (use with PC Connect Cable).
Start-Up Options Menu
See the following paragraphs for more information about each of these choices.
Normal Operation
Use Normal operation for on-the-water operation with a transducer connected. In
addition, your Matrix® Fishing System uses advanced transducer detection methods to
determine if a transducer is connected. If a functioning transducer is connected, Normal
operation will be selected automatically at power up and your Matrix® Fishing System
can be used on the water.
Exit Normal operation by powering your Matrix® Fishing System off.
22
Simulator
Use the Simulator to learn how to use your Matrix® Fishing System before taking your boat
on the water. The Simulator is a very powerful tool that simulates on the water operation,
providing a randomly-updated display. We recommend going through this manual while
using the Simulator, since all of the menus function and affect the display the way they
actually do when in Normal operation.
NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the
Start-Up Options menu as opposed to letting your Matrix® Fishing System enter Simulator
automatically (as it will if a transducer is not connected and you do nothing during power up). Manually
selecting Simulator from the Start-Up Options menu allows you to pre-configure your Matrix® Fishing
System for on the water operation. Any menu changes you make will be saved for later use.
A message will appear on the display periodically to
remind you that you are using the Simulator.
Exit the Simulator by powering your Matrix® Fishing
System off.
Simulator
System Status
Use System Status to view system connections and to
conduct a unit self-test.
The following screens are displayed in turn when you
press the VIEW button when using System Status:
• Self Test
• Accessory Test.
System Status Self Test Screen
23
Self Test displays results from the internal diagnostic self test, including unit serial
number, Printed Circuit Board (PCB) serial number, software revision, total hours of
operation and the input voltage.
Accessory Test lists the accessories connected to the
system.
NOTE: The speed accessory will be detected only if the
paddlewheel has moved since your Matrix® Fishing System
was powered up.
Exit System Status by powering your Matrix® Fishing
System off.
System Status Accessory Test Screen
PC Connect
(With PC Connect Cable Only)
Use PC Connect to update the software of the Matrix® control head. This feature requires
the use of the PC Connect Cable. Complete instructions are included with the PC Connect
Cable accessory.
NOTE: The PC Connect Cable requires a separate purchase. For more information visit our website at
Exit PC Connect mode by powering your Matrix® Fishing System off.
24
Sonar X-Press™ Menu
The Sonar X-Press™ Menu provides access to the
settings most frequently-used. Press the MENU key
once while in any of the Sonar Views to access the
Sonar X-Press™ Menu.
Sonar X-Press™ Menu
25
3D Bottom Zoom
(3D Sonar, 3D/2D Sonar Combo Views Only)
3D Bottom Zoom provides a magnified image of the bottom, and is only available on the
X-Press™ Menu in the 3D Sonar View and the 3D/2D Sonar Combo View. Use 3D Bottom
Zoom to increase the detail of the bottom on the display.
To adjust the 3D Bottom Zoom:
1. Highlight 3D Bottom Zoom on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the 3D Bottom Zoom
setting. (Off, 1.5x, 2x, 2.5x, 3x, Default = Off)
3D Lower Range
(3D Sonar, 3D/2D Sonar Combo, 6-Beam Sonar Views Only)
3D Lower Range sets the deepest depth range that will be displayed, and is only available
on the X-Press™ Menu when you are in the 3D Sonar, 3D/2D Sonar Combo, or the 6-Beam
Sonar View. Automatic is the default setting. When in automatic mode, the lower range
will be adjusted by the unit to follow the bottom. Selecting a specific setting locks the depth
range into Manual mode.
For example, if you are fishing in 60 feet of water but are only interested in the first
30 feet (surface to a depth of 30 feet) you should set the Lower Depth Range limit to
30. The display will show the 0 to 30 foot range, allowing you to see a more detailed
view than you would see if the display went all the way to the bottom.
To adjust the 3D Lower Range:
1. Highlight 3D Lower Range on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Lower
Range setting. (AUTO, 10 to 240 feet, 3 to 75 meters [International Models Only],
Default = AUTO)
26
3D History
(3D Sonar, 3D/2D Sonar Combo Views Only)
3D History determines the speed at which the sonar information moves across the
display, and consequently the amount of history shown, and is only available on the
X-Press™ Menu when you are in the 3D Sonar or the 3D/2D Sonar Combo Views. A faster
speed shows less history and is preferred by most anglers; however, the sonar
information moves across the display quickly. A slower speed keeps the information on
the display longer, but the bottom becomes compressed and may be difficult to
interpret. Adjust 3D History to your personal preference.
To adjust the 3D History:
1. Highlight 3D History on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-Way Cursor Control keys to increase or decrease the 3D
History setting. (Most, 2 - 9, Least; Default = 6)
2D Sonar Window
(3D/2D Sonar Combo View Only)
2D Sonar Window sets the width of the 2-dimensional Sonar Window, and is only available
on the X-Press™ Menu when you are in the 3D/2D Sonar Combo View.
To adjust the 2D Sonar Window:
1. Highlight 2D Sonar Window on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the width of the 2D
Sonar Window. (Wide, Medium, Narrow, Default = Medium)
Reset View
(3D Sonar, 3D/2D Sonar Combo Views Only)
Reset View resets the orientation, 3D Bottom Zoom, and 3D Lower Range, and is only available
on the X-Press™ Menu when you are in the 3D Sonar or the 3D/2D Sonar Combo Views.
To Reset View:
1. Highlight Reset View on the Sonar X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to reset the view.
27
6-Beam Sensitivity
(6-Beam Sonar View Only)
6-Beam Sensitivity controls how much detail is shown on the display, and is only available
on the X-Press™ Menu when you are in the 6-Beam Sonar View only. Increasing the
sensitivity shows more sonar returns from small baitfish and suspended debris in the
water; however, the display may become too cluttered. When operating in very clear
water or greater depths, increased sensitivity shows weaker returns that may be of
interest. Decreasing the sensitivity eliminates the clutter from the display that is
sometimes present in murky or muddy water. If Sensitivity is adjusted too low, the display
may not show many sonar returns that could be fish.
To adjust the 6-Beam Sensitivity:
1. Highlight 6-Beam Sensitivity on the Sonar X-Press ™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the 6-
Beam Sensitivity setting. (Low = 1, High = 20, Default = 10)
Sensitivity
(2D Sonar, 2D Zoom, 2D Big Digits Views Only)
Sensitivity controls how much detail is shown on the display, and is only available on the X-Press™
Menu when you are in the 2D Sonar, 2D Zoom, 2D Big Digits Views only. Increasing the sensitivity
shows more sonar returns from small baitfish and suspended debris in the water; however, the
display may become too cluttered. When operating in very clear water or greater depths,
increased sensitivity shows weaker returns that may be of interest. Decreasing the sensitivity
eliminates the clutter from the display that is sometimes present in murky or muddy water. If
Sensitivity is adjusted too low, the display may not show many sonar returns that could be fish.
Sensitivity at Low
Sensitivity at Medium
Sensitivity at High
To adjust the Sensitivity:
1. Highlight Sensitivity on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the
Sensitivity setting. (Low = 1, High = 20, Default = 10)
28
Upper Range
(Advanced: 2D Sonar, 2D Big Digits Views Only)
Upper Range sets the shallowest depth range that will be displayed. The Upper Range menu
choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode) and
is only available on the X-Press™ Menu when you are in the 2D Sonar or 2D Big Digits Views.
Upper Range is often used with Lower Range.
For example, if you are only interested in the area between 20 and 50 feet deep, you
should set the Upper Depth Range to 20 and the Lower Depth Range to 50. The 2D
Sonar View will then show the 30 foot area between 20 and 50, and will not show the
surface or the bottom (assuming the bottom is deeper than 50 feet), and will show
greater detail for that area between 20 and 50 feet.
NOTE: A minimum distance of 10 feet will be maintained between the Upper and Lower Range
regardless of the manual settings entered.
To adjust the Upper Range:
1. Make sure you are in Advanced Mode, then highlight Upper Range on the Sonar X-
Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Upper
Range setting. (0 to 990 feet or 0 to 327 meters [International Models Only], Default
= 0)
29
Lower Range
(2D Sonar, 2D Zoom, 2D Big Digits Views Only)
Lower Range sets the deepest depth range that will be displayed, and is only available on
the X-Press™ Menu when you are in the 2D Sonar, 2D Zoom, or 2D Big Digits Views.
Automatic is the default setting. When in automatic mode, the lower range will be
adjusted by the unit to follow the bottom. Selecting a specific setting locks the depth
range into Manual mode. Use both Upper and Lower Range together to view a specific
depth range manually when looking for fish or bottom structure.
in the lower right corner of the screen when you start manually adjusting the Lower
Range to indicate that you are in Manual mode.
will be displayed
M
For example, if you are fishing in 60 feet of water but are only interested in the first
30 feet (surface to a depth of 30 feet) you should set the Lower Depth Range limit to
30. The display will show the 0 to 30 foot range, allowing you to see a more detailed
view than you would see if the display went all the way to the bottom.
NOTE: A minimum distance of 10 feet will be maintained between the Upper and Lower Range
regardless of the manual settings entered.
To adjust the Lower Range:
1. Highlight Lower Range on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Lower
Range setting. (AUTO, 10 to 1000 feet, 3 to 330 meters [International Models Only],
Default = AUTO)
30
Chart Speed
(2D Sonar, 2D Zoom, 2D Big Digits Views Only)
Chart Speed determines the speed at which the sonar information moves across the display,
and consequently the amount of detail shown, and is only available on the X-Press™ Menu
when you are in the 2D Sonar, 2D Zoom, or 2D Big Digits Views. A faster speed shows more
information and is preferred by most anglers; however, the sonar information moves across
the display quickly. A slower speed keeps the information on the display longer, but the
bottom and fish details become compressed and may be difficult to interpret. Regardless of
the Chart Speed setting, the RTS™ Window will update at the maximum rate possible for
the depth conditions. Adjust Chart Speed to your personal preference.
To adjust the Chart Speed:
1. Highlight Chart Speed on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-Way Cursor Control keys to increase or decrease the Chart
Speed setting. (1 - 9, Ultra, where 1 = Slow, Ultra = Fastest, Default = 8)
Bottom View
(2D Sonar, 2D Zoom, 2D Big Digits Views Only)
Bottom View selects the method used to represent bottom and structure on the display,
and is only available on the X-Press™ Menu when you are in the 2D Sonar, 2D Zoom, or 2D
Big Digits Views. Inverse represents weak returns as dark pixels and strong returns as lighter
pixels. This has the benefit of ensuring that weak signals will be clearly visible on the display.
Structure ID® represents weak returns as light pixels and strong returns as dark pixels. This
has the benefit of ensuring that strong returns will be clearly visible on the display.
WhiteLine™ highlights the strongest sonar returns in white resulting in a distinctive outline.
This has the benefit of clearly defining the bottom on the display. Bottom Black displays all
pixels below the bottom contour as black, regardless of signal strength. This has the benefit
of providing a high contrast between the bottom and other sonar returns on the display.
Any targets such as fish, structure and thermoclines will be shown using the Structure ID®
method. See Bottom Presentation for more information.
To adjust the Bottom View:
1. Highlight Bottom View on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Bottom View
setting. (Inverse, Structure ID, WhiteLine, Bottom Black, Default = Inverse)
31
Zoom Level
(2D Zoom View Only)
Zoom Level sets the magnification level for the 2D Zoom View, and is only available on the
X-Press™ Menu when you are in the 2D Zoom View. Use Zoom to increase the display
resolution to separate sonar returns that are very close together.
To adjust the Zoom Level:
1. Highlight Zoom Level on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Zoom Level setting
for the 2D Zoom View. (2x, 4x, 6x, 8x, Default = 2x)
NOTE: The Zoom Preview Box tracks the bottom and cannot be moved by the user.
32
Sonar Menu Tab
Press the MENU key twice to access the Main Menu System
and then press the RIGHT 4-WAY Cursor Control key to select
the Sonar tab.
Sonar Menu
33
3D Bottom Style
3D Bottom Style selects the bottom style used in the 3D
Sonar View.
To change the 3D Bottom Style setting:
1. Highlight 3D Bottom Style on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the 3D Bottom Style
setting. (Grid Only, Shaded with Grid, Shaded, Default = Shaded with Grid)
3D Frame Style
3D Frame Style selects the frame style used in the 3D
Sonar View.
To change the 3D Frame Style setting:
1. Highlight 3D Frame Style on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the 3D Frame Style
setting. (Simple, 2, 3, 4, Complex, Default = 3)
Beam Select
Beam Select sets which sonar returns from the transducer will
be displayed on the screen.
When Beam Select is set to 455 kHz, the returns from the 455 kHz narrow beams will be
displayed in all views, and the maximum depth capability of your unit will be 240 ft (75 m).
When the depth is greater than 240 ft (75 m), Beam Select should be set to 83 kHz. The unit will
continue to acquire sonar returns below 240 ft and will be displayed in the 2D Sonar View.
NOTE: It is important to re-set Beam Select to 455 kHz when returning to water shallower than
240 ft (75 m) for maximum performance in the 3D views.
To change Beam Select:
1. Highlight Beam Select on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to select either the 455 kHz beam
or the 83kHz beam. (455 kHz, 83 kHz, Default = 455 kHz)
34
Fish ID+™
Fish ID+™ uses advanced signal processing to interpret
sonar returns, and will display a Fish Symbol when very selective requirements are met.
When a fish is detected, a fish icon and its depth are displayed above the return that has
been classified as being a fish. Fish symbols come in three different sizes to indicate
the intensity of the return; in addition, there is a unique symbol set associated with
each of the six beams, for a total of 18 possible fish symbols which can be displayed.
The following graphic illustrates the different Fish ID+™ symbols and shows the beams
with which they are associated. For instance, a hollow fish facing left indicates it was
detected in the far left beam and a hollow fish facing right indicates it was detected in
the far right beam.
When Fish ID+™ is turned off, the Fishing System shows only the raw sonar returns on
the display.
To set Fish ID+™:
1. Highlight Fish ID+ on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish ID+ setting.
(Off, Symbol Only, Symbol+Depth, Default = Symbol+Depth)
35
Fish Sensitivity
Fish Sensitivity adjusts the threshold of the Fish ID+™
detection algorithms. Selecting a higher setting allows weaker returns to be displayed
as fish. This is useful for identifying smaller fish species or baitfish. Selecting a lower
setting displays fewer fish from weak sonar returns. This is helpful when seeking larger
species of fish. Fish Sensitivity is used in conjunction with Fish ID+™. Fish ID+™ must be
set to either Symbol Only or Symbol+Depth for Fish Sensitivity to affect the ability of
your Matrix® Fishing System to identify sonar returns as fish.
To change the Fish Sensitivity setting:
1. Highlight Fish Sensitivity on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish Sensitivity
setting. (Low = 1, High = 10, Default = 5)
Fish ID 3D Reference
Fish ID 3D Reference selects the reference line style used in
the 3D Sonar View. Up draws a line from the fish icon to the surface plane, Down draws
a line from the fish icon to the bottom contour, and Both draws both lines.
To change the Fish ID 3D Reference setting:
1. Highlight 3D Fish ID Reference Line on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish ID 3D Reference
setting. (Surface, Both, Bottom, Default = Bottom)
36
Real Time Sonar (RTS™) Window
RTS™ Window sets the RTS™ Window to either Wide or
Narrow, or turns it off in the 3D or 2D Sonar Views. The RTS™ Window always updates at
the fastest rate possible and only displays returns that are within the transducer beam.
(See Real Time Sonar (RTS™) Window for additional detail).
RTS™ Window (Wide)
RTS™ Window (Narrow)
RTS™ Window (Off)
To change the RTS™ Window setting:
1. Highlight RTS Window on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the RTS™ Window
setting. (Wide, Narrow, Off, Default = Wide)
37
Depth Lines
(Advanced)
Depth Lines divide the display into four equal sections which are separated by three
horizontal depth lines. The depth of each line is displayed along the depth scale. You can
either turn Depth Lines On or Off. The Depth Lines menu choice is available when User Mode
is set to Advanced (see Setup Menu Tab: User Mode).
Depth
Lines
Depth Lines
To change the Depth Lines setting:
1. Make sure you are in Advanced User Mode, then highlight Depth Lines on the
Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn the Depth Lines setting
On or Off. (Off, On, Default = On)
38
Surface Clutter
(Advanced)
Surface Clutter adjusts the filter that removes surface clutter noise caused by algae and
aeration. The lower the setting, the less surface clutter will be displayed. The Surface Clutter
menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).
Surface
Clutter
To change the Surface Clutter setting:
1. Make sure you are in Advanced User Mode, then highlight Surface Clutter on the
Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Surface Clutter
setting. (Low = 1 to High = 10, Default = 5)
Noise Filter
(Advanced)
Noise Filter adjusts the sonar noise filter to limit interference on the display from sources
such as your boat engine, turbulence, or other sonar devices. The Noise Filter menu choice is
available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).
NOTE: The Off setting removes all filtering; Low, Medium and High settings add progressive filtering
of the sonar returns. In some deep water situations, the High setting may actually hinder your unit’s
ability to find the bottom.
To change the Noise Filter setting:
1. Make sure you are in Advanced User Mode, then highlight Noise Filter on the Sonar
main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Noise Filter setting.
(Off, Low, Medium, High, Default = Low)
39
Max Depth
(Advanced)
Max Depth adjusts the maximum depth of operation. The performance of your Matrix®
Fishing System can be tuned to the maximum depth you will be fishing in by setting the Max
Depth. When a maximum depth is set, your unit will not attempt to acquire sonar data
below that depth, thus increasing overall performance. When Max Depth is set to Auto, your
unit will acquire bottom readings as needed (within the depth capacity of the unit). If the
bottom is deeper than the Max Depth setting, the digital depth readout will flash, indicating
that your unit cannot locate the bottom. The Max Depth menu choice is available when User
Mode is set to Advanced (see Setup Menu Tab: User Mode).
To change the Max Depth setting:
1. Make sure you are in Advanced User Mode, then highlight Max Depth on the Sonar
main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Max Depth setting.
(AUTO, 10 to 1000 feet, 3 to 330 meters [International Models Only], Default =
AUTO)
Water Type
(Advanced)
Water Type configures your unit for operation in fresh or salt water. The Water Type menu
choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).
NOTE: In salt water, what would be considered a large fish might be 2 to 10 times bigger than a large
fish in fresh water (depending on the type of fish you are seeking). The salt water setting allows for a
greater range in fish size adjustment to account for this. Also, make sure that the Water Type is set
accurately, especially in salt water, as this affects the accuracy of deep water depth readings.
To change the Water Type setting:
1. Make sure you are in Advanced User Mode, then highlight Water Type on the Sonar
main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Water Type setting.
(Fresh, Salt, Default = Fresh)
40
Alarms Menu Tab
From any view, press the MENU key twice to access the
Main Menu System. The Alarms tab will be the default
selection.
NOTE: When an alarm is triggered, you can silence it by
pressing any key. The alarm will be silenced, and will not be
triggered again until a new instance of the alarm condition is
detected.
Alarms Menu
41
Depth Alarm
Depth Alarm sounds when the depth becomes equal to or less
than the menu setting.
To change the Depth Alarm setting:
1. Highlight Depth Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Alarm
setting. (OFF, 1 to 100 feet, or 0.5 to 30 meters [International Models Only], Default
= OFF)
Fish ID Alarm
Fish ID Alarm sounds when your Matrix® Fishing System
detects fish that correspond to the alarm setting. Fish ID
Alarm will only sound if Fish ID+™ is on.
For example, if you've set the Fish ID Alarm to sound for Large fish only, the
Fish ID Alarm will sound when a large-sized fish is detected.
To change the Fish ID Alarm setting:
1. Highlight Fish ID Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish ID Alarm
setting. (Off, All, Large/Medium, Large, Default = Off)
All
Large/Medium
Large
42
Low Battery Alarm
Low Battery Alarm sounds when the input battery voltage is
equal to or less than the menu setting. The battery alarm will only sound for the battery that
is connected to the Matrix® Fishing System. The Low Battery Alarm should be set to warn
you when the battery voltage drops below the safety margin that you have determined. For
instance, if you are running a trolling motor (battery operated), you would want to set the
Low Battery Alarm to sound before the battery voltage drops too low for it to be used to start
your main, gasoline-powered engine.
To change the Low Battery Alarm setting:
1. Highlight Low Battery Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Low Battery Alarm
setting. (Off, 8.5V - 13.5V, Default = Off)
Alarm Tone
Alarm Tone selects the pitch of the alarm sound. A brief tone
will be produced as you adjust the Alarm Tone so that you can
select the tone that you can hear best.
To change the Alarm Tone setting:
1. Highlight Alarm Tone on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Alarm Tone setting.
(High, Medium, Low, Default = Medium)
43
Setup Menu Tab
From any view, press the MENU key twice to access the
tabbed Main Menu System, then press the RIGHT
4-WAY Cursor Control key until the Setup tab is selected.
Setup Menu
44
Units - Depth
Units - Depth selects the unit of measure for all depth-related
readouts.
To change the Units - Depth setting:
1. Highlight Units - Depth on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Depth
setting. (Meters [International Models Only], Feet, Fathoms; Default is Meters for
International models, and Feet for Domestic models)
Units - Temp
(International Only)
Units - Temp selects the unit of measure for all temperature-related readouts. International
Models Only.
To change the Units - Temp setting:
1. Highlight Units - Temp on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Temp
setting. (Celsius, Fahrenheit; Default = Celsius)
Units - Distance
(with Temp/Speed or GPS Receiver)
Units - Distance selects the units of measure for all distance-related readouts, and will
appear in the menu if a Temp/Speed Accessory is connected and the paddlewheel has
moved at least once, or if a GPS Receiver is connected.
To change the Units - Distance setting:
1. Highlight Units - Distance on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Distance
setting. (Domestic Models: Statute Miles, Nautical Miles; Default = Statute Miles;
International Models: Meters/Kilometers, Meters/Nautical Miles, Feet/Statute
Miles, Feet/Nautical Miles; Default = Meters/Kilometers)
45
Units - Speed
(with Temp/Speed or GPS Receiver)
Units - Speed selects the unit of measure for speed-related readouts, and will appear in the
menu if a Temp/Speed Accessory is connected and the paddlewheel has moved at least
once, or if a GPS Receiver is connected.
To change the Units - Speed setting:
1. Highlight Units - Speed on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Speed
setting. (kph [International Models Only], mph, kts, Default = kph for International
models and mph for Domestic models)
User Mode
User Mode sets the menu system to either Normal or
Advanced. When set to Normal (default setting,) only the basic menu options are shown.
When set to Advanced, additional menu choices are available throughout the menu system.
To change the User Mode setting:
1. Highlight User Mode on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the User Mode setting.
(Normal, Advanced, Default = Normal)
Language
(International Only)
Language selects the display language for menus. International Models Only.
To change the Language setting:
1. Highlight Language on the Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Language setting.
(Default = English)
46
Triplog Reset
(with Temp/Speed or GPS Receiver)
Triplog Reset resets the Triplog to zero, and will appear in the menu if a Temp/Speed
Accessory is connected and the paddlewheel has moved at least once, or if a GPS Receiver is
connected. The Triplog provides the following information: timer for elapsed time, distance
traveled since last reset, and average speed.
NOTE: See Setup Menu Tab: Select Readouts to find out how to display Triplog information on
the screen.
To Reset Triplog:
1. Highlight Reset Triplog on the Setup main menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate Triplog Reset.
3. The Confirm dialog box will appear. To reset the Triplog, press the RIGHT
4-WAY Cursor Control key once more. To cancel Reset Triplog, press the LEFT 4-WAY
Cursor Control key.
Restore Defaults
Restore Defaults resets ALL menu settings to their factory
defaults. Use this menu choice with caution!
To Restore Defaults:
1. Highlight Restore Defaults on the Setup main menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate restoring defaults.
3. The Confirm dialog box will appear. To reset the defaults, press the RIGHT
4-WAY Cursor Control key once more. To cancel Restore Defaults, press the LEFT 4-
WAY Cursor Control key.
47
Select Readouts
(Advanced: 3D and 2D Sonar Views Only)
Select Readouts sets individual digital readouts on the 3D or 2D Sonar View. This Advanced
feature allows you to select what data will be displayed in each of 6 fixed-position data
windows arranged around the left and bottom edges of the 3D or 2D Sonar View screen, or
whether a particular data window will be turned off, displaying nothing in that area; you can
access this menu choice only when in Advanced User Mode (see Setup Menu Tab: User Mode.)
Data windows can display readouts from supported
accessories such as Temp/Speed. Each data window
can either be empty or contain one of the following:
-
Speed (will be displayed if a Temp/Speed
Accessory is attached and the paddlewheel has
moved at least once, or if a GPS Receiver is
connected)
- Temperature
- Triplog (will be displayed if a Temp/Speed Accessory
is attached and the paddlewheel has moved at least
once, or if a GPS Receiver is connected)
- Voltage
- Water Speed (will only be displayed if a
Temp/Speed Accessory is attached and the
paddlewheel has moved at least once). Water Speed
is not available with a GPS receiver.
Select Readouts
48
Default 2D Sonar View
Customized 2D Sonar View
To Select Readouts:
1. Make sure you are in Advanced User Mode, highlight Select Readouts on the Setup
main menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate this procedure.
3. The Select Readouts submenu will appear, showing a list of all Readouts. Use the UP
or DOWN Cursor Control keys to select a particular Readout position, then use the
RIGHT or LEFT Cursor Control keys to change what will be displayed at that position.
(Off, Speed, Temperature, Triplog, Voltage, Water Speed)
49
Depth Offset
(Advanced)
Depth Offset will adjust the digital depth readout to indicate depth from the waterline or
boat's keel. Enter a positive vertical measurement from the transducer to the waterline to
read the depth from the waterline. Enter a negative vertical measurement from the
transducer to keel to read the depth from the keel. This menu choice is available only when
in Advanced User Mode (see Setup Menu Tab: User Mode.)
To change the Depth Offset setting:
1. Make sure you are in Advanced User Mode, then highlight Depth Offset on the
Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Offset setting.
(-10.0 to +10.0 feet or -3 to 3 meters [International Models Only], Default = 0)
Temp Offset
(Advanced)
Temp Offset will adjust the temperature readout by the amount entered. This menu choice is
available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)
To change the Temp Offset setting:
1. Make sure you are in Advanced User Mode, then highlight Temp Offset on the Setup
main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Temp Offset
setting. (-10.0 to +10.0 degrees, Default = 0)
Speed Calibration
(Advanced: with Temp/Speed Only)
Speed Calibration will adjust the speed readout by the percentage entered, and will appear in the
menu if a Temp/Speed Accessory is connected and the paddlewheel has moved at least once,
when the unit is in Advanced User Mode (see Setup Menu Tab: User Mode.)
To change the Speed Calibration setting:
1. Make sure you are in Advanced User Mode, then highlight Speed Calibration on the
Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Speed Calibration
setting. (-20% to +20%, Default = 0%)
50
NMEA Output
(Advanced)
NMEA Output turns the NMEA output on or off. This menu choice is available only when in
Advanced User Mode (see Setup Menu Tab: User Mode.)
The following NMEA sentences are output:
DPT . . . . . . . . . . Depth
MTW . . . . . . . . Water Temperature
GLL . . . . . . . . . . Lat/Lon Position
GGA . . . . . . . . . GPS Fix Data
RMC . . . . . . . . . Recommended Minimum Specific GNSS Data
VTG . . . . . . . . . Course Over Ground and Ground Speed
ZDA . . . . . . . . . Time and Date
When navigating, the following NMEA sentences are also output:
APB . . . . . . . . . . Autopilot Sentence B
BWR . . . . . . . . . Bearing and Distance to Waypoint
RMB . . . . . . . . . Recommended Minimum Navigation Info
To turn NMEA Output on or off:
1. Make sure you are in Advanced User Mode, then highlight NMEA Output on the
Setup main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the NMEA Output to On
or Off (On, Off, Default = Off).
51
Views Menu Tab
From any view, press the MENU key twice to access the
tabbed Main Menu System, then press the RIGHT 4-
WAY Cursor Control key until the Views tab is selected.
This menu tab allows you to set the available views to
either hidden or visible in the view rotation. The view
will be removed from the view rotation if it is set to
Hidden and will be displayed in the view rotation if it is
set to Visible. The following views are available:
• 2D Sonar View
• 2D Zoom View
• 2D Big Digits View
• 3D Sonar View
• 3D/2D Sonar Combo View
• 6-Beam Sonar View
• Self Test
• Accessory Test.
Views Menu
To Change the View Status of Any View:
1. Highlight the View main menu tab.
2. Use the UP or DOWN 4-WAY Cursor Control keys to select a View.
3. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the status of the view
from Hidden to Visible.
52
Accessories Menu Tab
From any view, press the MENU key twice to access the tabbed Main Menu System, then
press the RIGHT 4-WAY Cursor Control key until the Accessories tab is selected. If no
accessories are attached to the Accessory Bus, no menu choices will appear under the
Accessories tab. If an accessory is attached, however, additional menu choices that support
the accessory will be added automatically. See the Operations Manual that comes with your
accessory for detailed information.
Accessories Menu
(no accessories attached)
Accessories Menu
(with accessories attached)
NOTE: Accessories to enable WeatherSense®, GPS Functionality and the SmartCast® Wireless Sonar
Customer Resource Center at 1-800-633-1468 for additional details.
53
Troubleshooting
Before contacting the Humminbird® Customer Resource Center, please read the following
section. Taking the time to review these troubleshooting guidelines may allow you to solve
a performance problem yourself, and therefore avoid sending your unit back for repair.
Matrix® Doesn’t Power Up
If your Matrix® Fishing System doesn’t power up, use the Installation Guide that also comes
with it for specific confirmation details, making sure that:
•
•
the power cable is properly connected to the Matrix® control head,
the power cable is wired correctly, with red to positive battery terminal and black
to negative terminal or ground
•
•
the fuse is operational
the battery voltage of the power connector is at least 10 Volts.
Correct any known problems, including removing corrosion from the battery terminals or
wiring, or actually replacing the battery if necessary.
Matrix® Defaults to Simulator with a Transducer Attached
A connected and functioning transducer will cause the newly-started Matrix® Fishing
System to go into Normal operating mode automatically. If, when you power up your unit,
it goes into Simulator mode automatically, even though a transducer is already connected,
this means that the control head is not detecting the transducer. Perform the following
troubleshooting tasks:
•
Using the Installation Guide that also comes with your Matrix® Fishing System,
check to make sure that the transducer cable is securely connected to your unit.
Reconnect if necessary, and power up the unit again to see if this fixes the problem.
•
•
Replace the non-functioning transducer with a known good transducer if available
and power up the control head again.
Check the transducer cable. Replace the transducer if the cable is damaged or
corroded.
54
Display Problems
There are several main conditions or sources of possible interference that may cause
problems with the quality of the information displayed on the control head. Look in the
following table for some symptoms of display problems and possible solutions:
Problem
Possible Cause
The control head loses power at
high speeds.
If the power output of your boat’s engine is
unregulated, the control head may be protecting
itself using its over-voltage protection feature. Make
sure the input voltage does not exceed 20 Volts.
When the boat moves at higher
speeds, the bottom disappears
or suddenly weakens, or the
display contains gaps.
The transducer position may need to be adjusted. A
mix of air and water flowing around the transducer
(cavitation) may be interfering with the inter-
pretation of sonar data. See your Installation Guide
for suggestions on adjusting the transducer position.
Electrical noise from the boat’s engine may be
interfering with sonar reception. See Finding the
Cause of Noise for more information.
There are no fish detected,
even when you know they are
in the water under the boat,
or sonar readings seem weak
or faulty.
Sonar readings may be affected if the transducer is
not positioned correctly (i.e. mounted at an angle, not
straight down), or there is some kind of mechanical
interference, either because it is mounted inside a
hull that is too thick for proper sonar transmission,
the bond between the transducer and the hull is not
airtight, or because the transducer is dirty. Check with
your Installation Guide for guidance on re-positioning
the transducer, and make sure the transducer is clean.
Low battery voltage may be affecting the power of
signal transmission.
Electrical noise from the boat’s engine may be
interfering with sonar reception. See Finding the
Cause of Noise for more information.
55
Finding the Cause of Noise
Electrical noise usually affects the display with many black dots at high speeds, and high
sensitivity readings. One or more of the following sources can cause noise or interference:
Possible Source of Noise
Other electronic devices
Isolation
Turn off any nearby electronic devices to see if the
problem goes away, then turn them on one at a time
to see if the noise re-appears.
The boat’s engine
To determine whether the boat’s engine is the source
of the noise, increase the RPMs while the boat is in
neutral and stationary to see if the noise increases
proportionately; if noise appears when you rev the
engine, the problem could be the spark plugs,
alternator, or tachometer wiring. Replace the spark
plugs with resistor plugs, install an alternator filter, or
route the control head power and transducer cables
away from the engine wiring.
Cavitation from the boat’s
propeller
Turbulence created by the propeller can cause noise;
make sure the transducer is mounted at least 15”
(38 cm) from the propeller, and that the water flows
smoothly over the face of the transducer at all times.
56
Matrix® Fishing System Accessories
Accessories customize the Matrix® Fishing System to your needs and enable you to stay on the
edge of new technology. When an accessory is connected to the Matrix® Fishing System,
additional menus and readouts are added automatically to the Main Menu System.
Accessories available today that are supported by your Matrix® Fishing System include:
Temperature/Speed: purchase and plug in the Temperature/Speed accessory to your
Matrix® control head to get real time speed and temperature readouts, as well as a valuable
Triplog function.
NOTE: If an external Temperature/Speed (TS-W) or Temperature (TG-W) accessory is connected AND a
transducer with temperature built in is connected at the same time, the TS-W or TG-W accessory will
override the temperature which is built in to the transducer.
WeatherSense® Fishing Condition Monitor: purchase and plug in the WeatherSense®
accessory to your Matrix® Fishing System to obtain barometric pressure readouts and trend
data in real time.
GR4 GPS Receivers: purchase and connect the GR4 GPS Receiver to your Matrix® Fishing
System to access advanced FishingGPS® , trackplotter and navigation capabilities built-in to
your Matrix® Fishing System.
GPS Connection Cable: purchase the GPS Connection Cable in order to connect a
handheld or other NMEA* GPS-compatible device that you may already own to your
Matrix® Fishing System.
Wireless Sonar Link (WSL): purchase the Wireless Sonar Link (WSL) accessory to receive remote
sonar signals from a SmartCast® Remote Sonar Sensor (RSS). Radio signals from the RSS are
received by the WSL and transmitted over the Accessory Bus to the Matrix® Fishing System.
PC Connect Cable: Purchase the PC Connect Cable to connect the Matrix® Fishing System to a
PC in order to upload product software updates and new features obtained from
www.humminbird.com. This accessory requires the MSWindows-compatible
HumminbirdPC™ software downloaded from our website to your PC in order to
communicate with the Matrix® Fishing System.
accessories to grow your Matrix® Fishing System!
or contact our Customer Resource Center at 1-800-633-1468 for additional details.
*NMEA 0183 is a National Marine Electronics Association standard for data communication.
57
Specifications
3D Depth Capability ................................................................................ 240 ft (75 m)
2D Depth Capability............................................................................ 1000 ft (330 m)
Power Output ................................................................................ 1000 Watts (RMS)
8000 Watts (Peak to Peak)
3D Operating Frequency .................................................................................. 455 kHz
2D Operating Frequency .................................................... 455 kHz to 240 ft (75 m)
83 kHz to 1000 ft (330 m)
3D Area of Coverage ............................................................ 53° @ -10 dB in 455 kHz
2D Area of Coverage ..............................................................60° @ -10 dB in 83 kHz
16° @ -10 dB in 455 kHz
Target Separation .................................................................... 2¹ꢀ₂ Inches (63.5 mm)
Power Requirement...................................................................................... 10-20 VDC
LCD Matrix .............................................................................................. 640 V x 320 H
Transducer .......................................................................................................... SHS-7W
Transducer Cable Length ............................................................................ 20 ft (6 m)
Product specifications and features are subject to change without notice.
58
Notes
59
Notes
60
®
Contact Humminbird
Contact the Humminbird Customer Resource Center
®
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
For direct shipping, our address is:
Humminbird
®
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
61
|