Hotpoint Ventilation Hood HT9X User Manual

Instructions for Installation and Use  
Electric Hood  
Model HT9X  
 
RECOMMENDATIONS AND SUGGESTIONS  
Using your new Cooker Hood is very simple. Nevertheless, to get the best results it is important  
that you read this manual thoroughly before installing and using your appliance for the first time.  
INSTALLATION  
• All installation and repairs should be carried out by a qualified  
technician in accordance to regulations in force.  
• The manufacturer will not be held liable for any damage resulting  
from incorrect or improper installation.  
• After having removed the packaging, check the condition of the  
appliance, if in any doubt, do not use and contact Hotpoint Service  
(see Key Contacts, back page).  
• The minimum safety distance between the hob and the extractor  
hood is 600 mm.  
• Check that the mains voltage corresponds to that indicated on the  
rating plate fixed to the inside of the hood.  
• For Class I appliances, check that the domestic power supply  
guarantees adequate earthing.  
• Connect the extractor to the exhaust flue through a pipe of minimum  
diameter 120 mm. The route of the flue must be as short as possible.  
• Do not connect the extractor hood to exhaust ducts carrying  
combustion fumes (boilers, fireplaces, etc.).  
• If the extractor is used in conjunction with non-electrical appliances  
(e.g. gas burning appliances), a sufficient degree of ventilation  
must be guaranteed in the room in order to prevent the backflow of  
exhaust gas. The kitchen must have a suitable vent to the outside  
of the building, so that clear fresh air can circulate through the  
kitchen.  
600mm min.  
USE  
• The extractor hood has been designed exclusively for domestic use  
to eliminate kitchen smells.  
• Never use the hood for purposes other than for which it has ben  
designed.  
• Never leave high naked flames under the hood when it is in  
operation.  
• Adjust the flame intensity to direct it onto the bottom of the pan  
only, making sure that it does not engulf the sides.  
• Deep fat fryers must be continuously monitored during use:  
overheated oil can burst into flames.  
• When frying, never leave the pan unattended.  
• The hood should not be used by children or persons not instructed  
in its correct use.  
MAINTENANCE  
• Switch off and unplug the appliance from the mains supply before  
carrying out any cleaning or maintenance work.  
• Clean regularly (see Care and Cleaning section), build up of dirt  
and grease could cause a fire hazard.  
GB  
3
 
INSTALLATION  
12  
G
13  
17  
F
1
4
16  
6
18  
15  
9
6
5
8
3
B
5
7
2
11  
11  
14  
14  
10  
11  
14  
11  
14  
Fig.1A  
GB  
4
 
INSTALLATION  
Consult Fig.1A on page 4 of this manual, referenced in the text by alphabet letters. Closely follow the instructions  
set out in this manual. All liability, for any inconvenience, damage or fires caused by not complying with the  
instructions in this manual, is declined.  
The cooker hood must be placed at a minimum distance of 60 cm from the hob top for electric cookers and 75cm  
for gas or mixed cookers.  
The hood is equipped with a top air outlet B for discharge of fumes to the outside (Ducting version exhaust pipe  
and pipe fixing clamps not provided).  
Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the filter  
version, fitting an activated carbon filter and the deflector F  
onto the support (bracket) G. Fumes and vapours are recycled through the top grille H by means of an exhaust  
pipe connected to the top air outlet B and the connection ring mounted on the deflector F (exhaust pipe and pipe  
fixing clamps not provided).  
The models with no extraction motor only operate in ducting mode, and must be connected to an external extraction  
device (not supplied).  
Preliminary information for installation of the hood:  
Disconnect the hood during electrical connection, by turning the home mains switch off.  
First decide which functioning version is better for you.  
If you decide to use the hood in ducting version we suggest you position the upper section of the chimney so that  
the oulet slots are not visible once installation has ended. If it is decided to use the hood in filter version BE SURE  
that the side with slots is up (see also 1-2-3 sequence on Fig. 1A).  
-
Using a pencil, draw a line on the wall, extending up to the ceiling, to mark the centre. This will facilitate  
installation.  
Rest the drilling template against the wall: the vertical centre line printed on the drilling template must  
correspond to the centre line drawn on the wall, and the bottom edge of the drilling template must correspond  
to the bottom edge of the hood: bear in mind that, when installation is complete, the underside of the hood  
must be at least 60 cm above the hob top in the case of electric cookers, and at least 75 cm above the cooker  
top in the case of gas or mixed cookers.  
-
-
Rest the support bracket on the drilling template so that it coincides with the dotted rectangle, mark the two  
outer holes and drill them, remove the drilling template, insert 2 wall plugs and fix the hood support bracket  
into place using two 5x45mm screws.  
-
-
-
-
Hang the hood on the bracket.  
Adjust the distance of the hood from the wall.  
Adjust the horizontal position of the hood.  
From inside the extraction unit, use a pencil to mark the hole (4 holes) to be used for final fixing of the hood.  
Remove the hood from the bracket. Drill at the points marked (2 x Ø8mm).  
Insert 4 wall plugs.  
-
-
Rest the chimney support bracket G against the wall, touching the ceiling. Use the support bracket as a  
drilling template (the small slot formed on the support must coincide with the line drawn on the wall as above  
– operation 4) and mark 2 holes with a pencil, dril the holes (Ø8mm), insert 2 wall plugs.  
Fix the chimney support bracket to the wall using two 5x45mm screws.  
Hook the hood onto the bottom bracket.  
Fix the hood into its final position on the wall using 4 5x45mm screws (ABSOLUTELY ESSENTIAL).  
Connect a pipe (pipe and pipe clamps not provided, to be purchased separately) for discharge of fumes.  
If the hood is to be used in the ducted version, the other end of the pipe must be connected to a device expelling  
the fumes to the outside. If the hood is to be used in filter version, fix deflector F to the chimney support bracket  
G using 4 screws, and connect the other end of the pipe to the connection ring on deflector F (if dismantled,  
the connection ring must be bayonet-fastened on the deflector and locked in position using 1 screw).  
Make the electrical connections (see next page).  
-
-
-
-
-
-
-
Apply the chimney stacks and fasten them at the top to the chimney support G using 2 screws.  
Slide the bottom section of the chimney down until it completely covers the suction unit and slots into the  
housing provided on top of the hood.  
Refit the grease filter/s and check that the hood is operating correctly.  
GB  
5
 
Electrical Connection  
WARNING: This appliance MUST be earthed. Connect to a 230 - 240V A.C. Supply only.  
Connection to the electricity supply should be made via a properly earthed, readily accessible  
wall socket which is adjacent to and not more than 1.25m away from the appliance and capable of  
electrical isolation.  
Should this plug not fit the socket outlet in your home it should be cut off and replaced with a  
suitable plug as outlined below.  
Note: The removed plug cannot be used for any other appliance and should therefore be properly  
disposed of and not left where children might find it and plug it into a supply socket - with the  
obvious consequent danger.  
IF THE FITTED PLUG IS REMOVED  
The flexible mains lead must be correctly connected as below, to a three pin plug of not less than 13  
amp capacity. If a B.S.1363 fused plug is used, it must be fitted with a 3amp fuse which is approved  
to B.S.1362.  
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with  
the following code:  
GREEN and YELLOW - EARTH  
BLUE - NEUTRAL  
BROWN - LIVE  
3amp FUSE  
CORD CLAMP  
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured  
markings identifying the terminals in your plug, proceed as follows:- The wire which is green and  
yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth  
symbol or coloured green or green and yellow. The wire which is coloured blue must be connected  
to the terminal which is marked with the N or coloured black. The wire which is coloured brown  
must be connected to the terminal which is marked with the letter L or coloured red. When wiring the  
plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the  
mains lead clamp on the plug. As the appliance must be earthed, DO NOT use 2-pin socket outlets,  
if you are in doubt, consult a qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried out by a  
2
qualified electrician and should only be replaced with a flexible cord of the same size ie. 0.75mm  
cross sectional area and temperature rating of 85°C eg. heat resisting PVC.  
IF A MOULDED PLUG IS FITTED  
In the event of replacing a fuse in the plug supplied a 3amp ASTA approved fuse to B.S.1362 must  
be fitted.  
Note: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover  
the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse  
cover can be obtained from your local Electrical Retailer. The colour of the correct replacement fuse  
cover is that of the coloured marks or inserts in the base of the plug.  
GB  
6
 
7
6
1
4
f1  
2
f2  
2
5
3
2
Fig. 1 1  
Fig. 2 2  
a
c
b
a
c
b
Fig. 4 4  
Fig. 3
GB  
7
 
GETTING TO KNOW YOUR COOKER HOOD  
The Controls  
WARNING: Children should not be allowed to play  
with the appliance or tamper with the controls.  
a
b
c d  
e
a
Light  
Switches the lighting system on and off.  
Switches the extractor motor on and off at low speed.  
Increases the operating speed.  
b
Motor  
Speed  
Speed  
b+c  
b+c+d  
b+c+d+e  
Increases the operating speed.  
Intensive Maximum operating speed.  
(see Fig.1)  
Features  
1
2
3
4
5
6
7
Control Panel  
Grease Filters  
Grease Filter Release Handle  
Light (Halogen)  
Vapour Screen  
Telescopic Chimney  
Air Outlet (used for Filter version only)  
GB  
8
 
CARE AND CLEANING  
Before you clean your Cooker Hood or carry out any maintenance, switch off and remove the plug from the socket  
to disconnect it from the electricity supply.  
(see Fig.2)  
GreaseFilters  
These must be cleaned once a month using non aggressive detergents, either by hand or in the dish-washer, which  
must be set to a low temperature and a short cycle.  
When washed in a dish-washer, the grease filter may discolour slightly, but this does not affect its filtering capacity.  
To remove the grease filter, pull the spring release handle (f).  
(see Figs.2 and 3)  
Carbon Filters  
It absorbs unpleasant odours caused by cooking.  
The active carbon filter must NEVER be washed.  
The active carbon filter should be changed every 4 months in normal use.  
Mounting and replacing the Carbon filters:  
a. Disconnect the hood from the electricity.  
b. Remove the grease filters (Fig. 2).  
c. If Carbon filters have not been previously installed, place one active carbon filter on each side so that they  
cover the grates protecting the rotor on the motor. Then turn the centre handle in the clockwise direction (Fig.  
3) to lock the filters in place.  
d. If the Carbon filters have already been installed (covering the grates protecting the rotor on the motor) and need  
to be replaced, turn the central handle in the counter-clockwise direction until the Carbon filters are unlocked.  
e. Refit the the metal grease filters.  
(see Fig.4)  
Replacing Lamps  
Firstly, if the lights do not work, make sure that the lamps are fitted properly into their housings. If  
they still don not work they are easy to replace.  
Replacement bulbs are available from Hotpoint Genuine Parts and Accessories (see Key Contacts, back page).  
Only use halogen bulbs of 20W max (G4), making sure you do not touch them with your hands.  
Access the light compartment: extract the guard by levering it off with a small screwdriver or similar tool (fig. 4).  
Make sure that the lamps have cooled before replacing them.  
Replace the burnt out light bulb.  
Close the lamp cover (it will snap shut).  
Cleaning  
Clean regularly, with a sponge soaked in warm water  
and a sodium bicarbonate solution, which is among  
otherthingsagooddisinfectant. Ifyoudonothaveany,  
youcanuseaneutralsoap.  
DONOTuseabrasivedetergents,bleachordetergents  
usingammonia. NEVERusesolventbasedproducts.  
WARNING:  
Failure to carry out the basic standards of cleaning and replacement of the filters could cause a fire risk. Therefore  
you must observe these instructions.  
GB  
9
 
After Sales Service  
"No company is better positioned to offer an after sales service on a  
Hotpoint appliance than us - the manufacturer"  
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive  
parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of  
free replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales  
service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number of your appliance  
Available 364 days a year with a fast, effective and value for money service. We have the largest  
white goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs  
include a parts and labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your appliance, our operators are on hand  
with help and advice.  
All this ensures that you will receive the best available after sales service possible.  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service  
cover plans to give you total peace of mind.  
Repair Protection Plan  
-
FREE service repairs for a single Hotpoint appliance during the  
period of cover.  
FREE service repairs for all your Hotpoint appliances less than  
Kitchen Cover  
-
8 years old.  
Genuine Parts and Accessories  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
A wide range of genuine parts and accessories are available from our hotline or through our website.  
Genuine parts and accessories, extended warranties and service repairs are all  
available on our web-site at:  
GB  
10  
 
Guarantee  
"Satisfaction guaranteed or your money back"  
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have  
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair  
for an engineer to call. If the technical problem is not resolved under this guarantee, we will  
replace your machine or, if you prefer, give you your money back.  
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free  
replacement parts for the first 5 years (except microwaves, selected integrated appliances and  
cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint  
engineer.  
Guarantee terms and conditions  
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to  
the following provisions that your appliance:  
Has been installed and used correctly in accordance with this instruction booklet.  
Has been used solely for domestic purposes and is located on domestic premises (ie. not  
for commercial or trade use).  
Has been properly connected to a suitable electrical supply voltage as stated on the  
appliance rating plate.  
Has not been subject to misuse, accident, modified or repaired by anyone other than one  
of our own service engineers.  
For pre purchase information on any other Hotpoint product call: 08701 50 60 70  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the  
right to use quality recycled components to keep down customer costs and minimise material  
wastage.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the plug and cut mains cable off flush with the  
appliance. Dispose of these parts separately to ensure that the appliance can no longer be  
plugged into a mains socket.  
GB  
11  
 
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete  
confidence in both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB.  
LI13ZA Ed. 01/03  
January 2003 Part no. FP172 - 01  
 

Graco Saw 334135B User Manual
Grizzly Cordless Sander G1072 User Manual
Haier Washer HWM75TLU User Manual
Hamilton Beach Air Cleaner 840121000 User Manual
Harbor Freight Tools Biscuit Joiner 96067 User Manual
Hasbro Games Sonic Hover Jet User Manual
HP Hewlett Packard Home Theater System de 1000c User Manual
HP Hewlett Packard Server BL495c User Manual
HTC Cell Phone MyTouch3GBLKTMB User Manual
Husqvarna Lawn Mower YTH2042XP User Manual