Hotpoint Dishwasher LFT04 User Manual

Instruction booklet  
DISHWASHER  
Contents  
EN  
Installation, 2-5  
Positioning and levelling  
Technical data  
English, 1  
Electrical connection  
Connecting the water supply  
Description of the appliance, 6  
Overall view  
Control panel  
Loading the racks, 7  
Lower rack  
Cutlery basket  
Upper rack  
Start-up and use, 8  
Starting the dishwasher  
Loading the detergent  
Washing options  
LFT 114  
LFT 04  
Wash cycles, 9  
Wash cycle table  
Rinse aid and refined salt, 10  
Loading the rinse aid  
Loading the refined salt  
Care and maintenance, 11  
Shutting off the water and electricity supplies  
Cleaning the dishwasher  
Preventing unpleasant odours  
Cleaning the sprayer arms  
Cleaning the water inlet filter  
Cleaning the filters  
Leaving the machine unused for extended periods  
Precautions and advice, 12-13  
General safety  
Disposal  
Saving energy and respecting the environment  
Troubleshooting, 14  
After Sales Service, 15  
After Sales Service  
Essential Contact Information  
Parts and Accessories  
Appliance Registration  
Hotpoint Guarantee, 16  
 
The dishwasher meets the requirements set out  
by the regulations in force concerning safety and  
electrical equipment.  
DO NOT use the plug unless the fuse cover is  
fitted.  
EN  
Changing the Plug  
Any technical checks should be conducted  
exclusively by a trained and authorised technician:  
Repairs carried out by unaithorised persons will  
invalidate the guarantee, as well as posing a  
potential hazard to the user.  
Cut off and dispose of the supplied plug if it  
does not fit your socket.  
To avoid a shock hazard DO NOT insert the  
discarded plug into a socket anywhere else.  
The manufacturer declines all responsibility for  
damage to persons or property resulting from failure  
to observe the above precautions, from tampering  
with even a single component or from the use of  
non-original spare parts.  
Wires in the mains lead are coloured accordance  
with the following code:  
Green/Yellow -  
Earth  
Neutral  
Live  
Blue  
-
-
Electrical Connection  
Brown  
Before inserting the plug into the electrical socket,  
make sure that:  
If you change the plug, the colour of the wires in the  
mains lead may not correspond with the terminal  
markings in the plug, which if not coloured, could  
be:  
the socket is earthed and complies with current  
regulations;  
EARTH  
NEUTRAL ‘N’  
LIVE ‘L’  
‘E’ or  
the socket can withstand the maximum load of  
the appliance, which is indicated on the data  
plate located on the inside of the door (see  
Description of the appliance);  
Changing the Mains Lead  
the power supply voltage falls within the values  
indicated on the data plate on the inside of the  
door;  
A lead can be ordered from Hotpoint Service  
UK: 08709 066 066 or  
Republic of Ireland: 1850 302 220  
the socket is compatible with the plug of the  
appliance. If this is not the case, ask an  
authorised technician to replace the plug (see  
Assistance); do not use extension cables or  
multiple sockets.  
- If you have damaged the existing lead or require a  
longer one a charge will be made. It is strongly  
advised that this work is carried out by a qualified  
electrician.  
- If the domestic wiring includes a residual current-  
operated circuit breaker, ensure that it conforms to  
the latest regulations.  
Once the appliance has been installed, the  
power supply cable and the electrical socket should  
be easily accessible.  
The dishwasher must not be connected to the  
electricity supply while installation is being carried  
out.  
The cable should not be bent or compressed.  
- This appliance should only be connected to a 230/  
240V AC source, via a properly installed earthed  
socket.  
If the power supply cable is damaged, it must  
be replaced by the manufacturer or its Technical  
Assistance Service in order to prevent all potential  
hazards. (See Assistance)  
- Use the dishwasher solely in a domestic  
environment.  
- DO NOT stand or place heavy objects on the door  
when it is open, this could damage the door or  
cause the appliance to tip forward.  
This appliance must be earthed.  
Fuses:your appliance comes fitted with a plug and a  
13A fuse. If you need to replace the fuse, only those  
rated at 13A and ASTA approved to BS1362 should  
be used. If you lose the fuse cover, a replacement  
may be obtained from your local authorised Service  
Centre or Electrical company. Correct replacement is  
identified by colour coding or the marking on base  
of plug.  
The Company shall not be held responsible for  
any incidents that occur if these regulations are not  
observed.  
3
 
Ensure that the new hose supplied is connected  
and the old hose is disposed of safely.  
Connecting the water supplies  
EN  
Connection to the water and electricity supplies  
should only be performed by a qualified technician.  
Ensure the fill hose is only fitted to the cold  
water supply. DO NOT overtighten the hose  
connector, hand tight is sufficient.  
The dishwasher should not stand on top of the  
water hoses or the electricity supply cable.  
Ensure the fill hose is not kinked.  
Connecting the water inlet hose  
Tap connections*: A range of adaptors are  
available to suit your tap.  
The water inlet (A) and outlet (B) hoses and the  
electricity supply cable may be positioned towards  
the right or the left in order to achieve the best  
possible installation (see figure).  
DO NOT connect the dishwasher to a single  
outlet instantaneous water heater or an electric  
heater.  
Standpipe  
Ensure that the hose is not pushed too far down the  
standpipe.  
If the end of your drain hose is fitted  
with ‘retaining flaps*’, ensure they are  
inserted fully into the standpipe. This  
will prevent the pipe from jumping out  
during installation and use.  
To a suitable cold water connection point: before  
attaching the hose, run the water until it is  
perfectly clear so that any impurities that may be  
present in the water do not clog the appliance;  
after performing this operation, screw the inlet  
hose tightly onto a tap with a ¾ gas threaded  
connection.  
DO NOT position the standpipe near an  
electrical outlet.  
ENSURE that the drain hose is not kinked and it  
is routed as shown in the diagram.  
The standpipe should have a bore of at least 38mm  
(11/2”). It should be installed as shown, have a trap  
fitted and must discharge into the same drain  
system as your household sink.  
To a suitable hot water connection point: your  
dishwasher may be provided with hot water from  
the mains supply (if you have a central heating  
system with radiators) provided that it does not  
exceed a temperature of 60°C.  
It MUST NOT be connected to a surface water  
drain.  
Screw the hose to the tap as described for  
connection to a cold water supply.  
If the inlet hose is not long enough, contact a  
specialist store or an authorised technician (see  
Assistance).  
The water pressure must be within the values  
indicated in the Technical data table (see  
Installation).  
The hose should not be bent or compressed.  
The appliance must be connected to the water  
supply network using new hoses.  
Do not use old hoses.  
* Only available in selected models.  
4
 
Sink Waste System  
Anti-flooding protection*  
EN  
For under sink drainage:  
To ensure floods do not occur, the dishwasher:  
- is provided with a special system which blocks the  
water supply in the event of anomalies or leaks from  
inside the appliance.  
• before connecting the drain hose, remove any  
internal restrictions; this will prevent a build up of  
debris which could cause a blockage  
• remove any restrictions from the waste spigot and  
ensure that the sealing bung is removed  
Some models are also equipped with the  
supplementary safety device New Acqua Stop*,  
which guarantees anti-flooding protection even in the  
event of a supply hose rupture.  
• the hose should be routed, such that it is raised  
to a minimum height of 800mm (31/2”).  
WARNING: HAZARDOUS VOLTAGE!  
Under no circumstance should the water inlet hose  
be cut as it contains live electrical parts.  
The Company shall not be held responsible for  
any incidents that occur if these regulations are not  
observed.  
Ensure the sink outlet pipe has a minimum  
diamtere of 32mm.  
• Untie the end of the  
GREY drainage hose from  
the rear of the appliance.  
• Reposition the ‘Hooked  
End Support’ as required  
along the GREY drainage  
hose.  
• If fitting an under sink waste disposal unit, cut out  
the membrane, bung or blanking plug.  
Ensure the drain hose is securely attached, to  
prevent it coming away while the machine is in  
use and causing a flood.  
* Only available in selected models.  
5
 
Description of the appliance  
Overall view  
EN  
1.  
Upper rack  
2.  
Upper sprayer arm  
Tip-up compartments  
Rack height adjuster  
Lower rack  
3.  
4.  
5.  
6.  
Lower sprayer arm  
Cutlery basket  
7.  
8.  
Washing filter  
9.  
Salt dispenser  
10.  
11.  
12.  
Detergent and rinse aid dispensers  
Data plate  
Control panel***  
Control panel  
ON/OFF  
indicator  
light  
WASH CYCLE  
indicator lights  
WASH CYCLE SELECT  
button  
ON/OFF/RESET  
button  
***Only in completely built-in models.  
* Only available in selected models.  
6
 
Loading the racks  
Before loading the racks, remove all food residues from the  
crockery and empty liquids from glasses and cups.  
After loading the appliance, check that the sprayer arms  
can rotate freely.  
Adjusting the height of the upper rack  
In order to make it easier to arrange the crockery, the upper  
rack may be moved to a higher or lower level.  
EN  
The height of the upper rack should ideally be adjusted  
WHEN THE RACK IS EMPTY.  
Lower rack  
The lower rack can hold pans, lids, plates, salad bowls, cutlery,  
Never lift or lower the rack on one side only.  
etc. as seen in the Loading examples.  
Plates and large covers should be placed at the sides of the  
rack, ensuring that they do not block the rotation of the upper  
sprayer arm.  
Open the left and right guide rail stops  
and pull out the rack; position it higher  
or lower as required, slide it along the  
guide rails until the front wheels are in  
place and close the stops (see  
figure).  
Some dishwasher models are fitted with tip-up sections*, which  
can be used in a vertical position when arranging plates or in a  
horizontal position when arranging pans and salad bowls.  
If the rack is fitted with Dual Space  
handles*(see figure), pull out the  
upper rack until it reaches its stop  
point, grip the handles at the sides of  
the rack and move it upwards or  
downwards, then slowly let it fall back  
into place.  
Cutlery basket  
The type of cutlery basket may vary according to the  
dishwasher model: it may be modular, non-modular or a sliding  
version. The non-modular basket must only be positioned at  
the front of the lower rack.  
Loading examples for the upper rack  
The modular basket may be separated into two parts, a solution  
which is recommended when performing a half load wash (only  
in models offering this option), is available in a sliding version  
(positioned at any point on the lower rack by sliding it between  
the fixed or tip-up inserts.  
- Both versions are fitted with a collapsible sliding system which  
means the cutlery can be arranged in the best possible way.  
Loading examples for the lower rack  
Knives and other utensils with sharp edges must be placed  
in the cutlery basket with the points facing downwards, or they  
must be positioned horizontally in the tip-up compartments on  
the upper rack.  
Items which should not be washed in the  
dishwasher  
Wooden items, objects with wooden or horn handles or  
glued-on parts.  
Cutlery basket positioning examples  
Items made from aluminium, copper, brass, pewter or tin.  
Items made from plastic material which is not heat-  
resistant.  
Antique or hand-painted porcelain.  
Antique silver. Silver which is not antique may, however, be  
washed in the dishwasher using a delicate wash cycle,  
provided that it does not come into contact with other  
metals.  
Upper rack  
Load this rack with delicate and lightweight crockery: glasses,  
tea and coffee cups, saucers, small salad bowls, saucepans  
and small saucepans which are not too soiled, using the  
Loading examples as a guide.  
We recommend the use of crockery which is dishwasher  
safe.  
• Mugs and cups: place these on the tip-up compartments**.  
• Long sharp knives and serving utensils: place these on the  
tip-up compartments**.  
7
 
Start-up and use  
Starting the dishwasher  
Measuring out the detergent  
EN  
1. Turn the water tap on.  
A good wash result also depends on the correct  
amount of detergent being used; exceeding the  
stated amount does not result in a more effective  
wash and increases environmental pollution.  
2. Open the door and press the ON/OFF button: you  
will hear a short beep and the ON/OFF and wash  
cycle indicator lights switch on for a few seconds.  
3. Measure out the detergent (see below).  
4. Load the racks (see chapter entitled Loading the  
racks).  
Only use detergent which has been  
specifically designed for dishwashers.  
5. Select the wash cycle in accordance with the type  
of crockery and its soil level (see Table of wash  
cycles), by pressing the P button; the indicator light  
corresponding to the selected wash cycle will switch  
on.  
DO NOT USE washing up liquid.  
Using excessive detergent may result in foam  
residue remaining in the machine after the cycle  
has ended.  
7. Start the wash cycle by shutting the door: after a  
few seconds have passed, a long beep signals the  
start of the wash cycle.  
The use of tablets is only recommended for  
models which offer the MULTI-FUNCTIONAL  
TABLETS option.  
8. Two short beeps and one long one indicate the end  
of the wash cycle and the indicator light  
corresponding to the wash cycle flashes slowly. Open  
the door, switch off the appliance by pressing the ON/  
OFF button, shut off the water tap and unplug the  
appliance from the electricity socket.  
To achieve the best results from each washing  
and drying cycle, powder detergent, rinse aid  
liquid and salt should be used.  
Compartment A: Washing detergent  
Compartment B: Pre-wash detergent  
9. Wait for a few minutes before removing the  
crockery, in order to avoid burns. Unload the racks,  
beginning with the lower level.  
1. Open cover C by pressing  
button D.  
2. Pour in the detergent after  
consulting the Table of wash  
The order in which the different wash programmes  
are displayed will change according to the frequency  
with which each cycle is used.  
cycles:  
• For powder detergent use  
compartments A and B.  
• For detergent in tablet form:  
Modifying a wash cycle in progress  
when the cycle requires 1 tablet,  
place it in compartment A and close the cover; when it  
requires 2, place the second tablet at the bottom of the  
appliance.  
If a mistake was made during the wash cycle selection  
process it is possible to change the cycle, provided that  
it has only just begun: open the door, taking care to  
avoid the escaping steam, and press and hold the ON/  
OFF button; the machine will switch off with a long beep.  
Switch the machine back on using the ON/OFF button  
and select the new wash cycle using the P button; start  
the cycle by closing the door.  
3. Remove detergent residues from the edges of the  
compartment and close the cover until it clicks.  
Adding extra crockery  
Without switching off the machine, open the door,  
taking care to avoid the escaping steam, and place  
the crockery inside the dishwasher. Close the door:  
the cycle starts from the point at which it was  
interrupted.  
Accidental interruptions  
If the door is opened during the wash cycle, or if there  
is a power cut, the cycle stops. It starts again from the  
point at which it was interrupted once the door has  
been shut or the electricity supply is restored.  
*Only available in selected models.  
8
 
Wash cycles  
Wash cycle table  
EN  
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dish-  
washer, reduce the amount of detergent used accordingly.  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
Wash cycle  
duration  
Drying (tolerance  
10%)  
Detergent  
(A) = compartment A  
(B) = compartment B  
Wash cycle  
Selection  
instructions  
Wash  
cycle  
Powder  
Liquid  
Tablets  
Hrs. Min.  
Extremely soiled dishes  
and pans (not to be  
used for delicate items).  
30 g (A) 30 ml (A)  
1 (A)  
1 (A)  
Yes  
Yes  
2:15’  
1:45’  
Intensive  
Normal  
Normally soiled pans  
and dishes. Standard  
daily wash cycle.  
25 g (A) 25 ml (A)  
5 g (B)  
5 ml (B)  
Preliminary wash cycle  
for dishes while the load  
is awaiting completion  
with the dishes from the  
next meal.  
No  
No  
No  
No  
0:08’  
2:20’  
Soak  
Environmentally-friendly  
wash cycle* with low  
energy consumption  
levels, suitable for pans  
and dishes.  
25 g (A) 25 ml (A)  
5 g (B) 5 ml (B)  
1 (A)  
Yes  
Note  
To make it easier to measure out the detergent, it is worth remembering that:  
1 tablespoon = 15 grams of powder = approximately 15 ml of liquid  
1 teaspoon = 5 grams of powder = approximately 5 ml of liquid  
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it  
uses less energy and is les harmful to the environment.  
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the  
following address: [email protected]  
9
 
Rinse aid and refined salt  
Only use products which have been  
specifically designed for dishwashers.  
Do not use table salt or industrial salt, or  
washing up liquid.  
number 3).  
EN  
- Press the P button repeatedly until the desired hardness  
level has been reached (1-2-3-4-5*see Water hardness  
table).  
Follow the instructions given on the packaging.  
E.g. Hardness level 1 (1st cycle indicator light flashing)  
Hardness level 2 (1st cycle indicator light ON, 2nd cycle  
indicator light flashing)  
If using a multi-functional product it is not necessary to  
add rinse aid; however, we recommend that you add salt,  
especially if you live in an area where the water is hard or  
very hard. Follow the instructions given on the packaging.  
Hardness level 3 (1st and 2nd cycle indicator lights ON, 3rd  
cycle indicator light flashing etc) up to maximum 5 levels*.  
- To exit the function, wait approximately 30 seconds or switch  
off the machine using the ON/OFF button.  
If you do not add salt or rinse aid, the LOW  
SALT* and LOW RINSE AID* indicator lights  
remain lit.  
Even if using multi-functional tablets, the salt dispenser should  
still be filled.  
Water Hardness Table  
°dH  
°fH  
mmol/l  
level  
Measuring out the rinse aid  
Rinse aid makes it easier for the crockery to dry, as water  
runs off surfaces more readily and therefore does not leave  
streaks or marks.  
0
11  
0
20 1.1  
2
3
6
9
1
2
3
12 17 21  
17 34 31  
34 50 61  
30 2.1  
60 3.1  
90 6.1  
*
4
The rinse aid dispenser should be filled:  
• When the LOW RINSE AID*indicator light on the control  
panel is illuminated;  
For values between 0°f and 10°f, we do not  
recommend the use of salt.  
* this setting may cause a slight increase in the  
duration of the cycle.  
1. Open the dispenser by turning  
H
(°dH = hardness measured in German degrees - °f =  
hardness measured in French degrees - mmol/l = millimoles  
per litre)  
the lid (G) in an anticlockwise  
direction.  
2. Pour in the rinse aid, making sure  
it does not overflow from the  
dispenser. If this happens, clean  
Measuring out the refined salt  
In order to achieve the best possible results using a wash  
cycle, make sure that the dispenser is never empty. Refined  
salt removes limescale from the water, thus avoiding the  
formation of deposits on crockery.  
F
the spill immediately with a dry  
G
cloth.  
3. Screw the lid back on.  
NEVER pour the rinse aid directly into the appliance tub.  
The salt dispenser is located in the lower part of the  
dishwasher (see Description) and should be filled:  
• When the green float*cannot be seen by simply looking at  
the cap of the salt dispenser.  
Adjusting the amount of rinse aid  
If you are not completely satisfied with the drying results, you  
may adjust the quantity of rinse aid used. Use a screwdriver  
to turn the dosage adjuster (F) to one of the 6 pre-set  
positions (the default position is set to 4):  
• When the LOW SALT*indicator light on the control panel is  
illuminated;  
• If there are streaks on the crockery, set the adjustment  
device to a lower number (1-3).  
1. Remove the lower rack and unscrew  
the container cap (anticlockwise).  
• If drops of water remain on the crockery or if there are  
limescale marks present after the cycle has finished, set the  
adjuster to a higher number (4-6).  
2. The first time you do this: fill the water  
tank right up to its edge.  
3. Position the funnel*(see figure) and fill  
the salt container right up to its edge (this  
Setting the water hardness  
should hold approximately 1 kg); it is not  
Every dishwasher is equipped with a water softener which, by  
using refined salt designed especially for this type of  
appliance, supplies water without limescale which is then used  
to wash the crockery.  
unusual for a little water to leak out.  
4. Remove the funnel* and wipe any salt residue away from the  
opening; rinse the cap under running water and then screw it  
on, the head facing downwards so as to let the water flow out  
of the four cracks which are arranged in a star shape on the  
lower part of the cap. (the container cap with the green float*)  
It is advisable to perform this procedure every time you  
add salt to the container.  
This dishwasher offers a setting which helps to reduce  
pollution and optimises washing performance in accordance  
with the water hardness level in your area. This information can  
be obtained from the organisation which supplies your  
household with water.  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash cycle (this could  
damage the water softener beyond repair).  
- Open the door and switch on the machine by pressing the  
ON/OFF button.  
- Press the P button and hold for approximately 5 seconds;  
two short beeps will sound and the indicator light  
corresponding to the set degree of hardness will flash slowly  
on the control panel (the water softening system is set to  
When necessary, measure out the salt before a wash  
cycle so that any saline solution which has leaked out of the  
salt dispenser is removed.  
*Only available in selected models.  
10  
 
Care and maintenance  
Clean the water inlet filter at the tap outlet regularly.  
Shutting off the water and electricity  
supplies  
•Turn off the water tap after every wash cycle to avoid  
EN  
- Turn off the water tap.  
- Unscrew the end of the water inlet hose, remove the  
filter and clean it carefully under running water.  
- Replace the filter and screw the water hose back into  
leaks.  
•Always unplug the appliance when cleaning it and  
position.  
when performing maintenance work.  
Cleaning the filters  
The filter assembly consists of three filters which remove  
Cleaning the dishwasher  
•The external surfaces of the machine and the control  
food residues from the washing water and then  
panel may be cleaned using a non-abrasive cloth  
which has been dampened with water. Do not use  
solvents or abrasive products.  
recirculate the water. They should be cleaned if you wish  
to achieve the best results in every wash.  
Clean the filters regularly.  
•Any marks on the inside of the appliance may be  
removed using a cloth dampened with water and a  
little vinegar.  
The dishwasher should not be used without filters, or  
if the filter is loose.  
• After several washes, check the filter assembly and if  
necessary clean it thoroughly under running water,  
Preventing unpleasant odours  
•Always keep the door of the appliance ajar in order  
using a non-metallic brush and following the instructions  
to avoid moisture from forming and being trapped  
inside the machine.  
below:  
1. Turn the cylindrical filter C in an anti-clockwise  
direction and pull it out (fig. 1).  
•Clean the seals around the door and detergent  
dispensers regularly using a damp sponge. This will  
avoid food becoming trapped in the seals, which is  
the main cause behind the formation of unpleasant  
odours.  
2. Remove the cup filter B by exerting a slight pressure  
on the side flaps (fig. 2).  
3. Slide out the stainless steel plate filter A (fig. 3).  
4. Inspect the trap and remove any food residue. NEVER  
REMOVE the wash cycle pump (black detail) (fig. 4).  
Cleaning the sprayer arms  
Food residue may become encrusted onto the sprayer  
arms and block the holes used to spray the water. It is  
therefore recommended that the arms are checked from  
time to time and cleaned with a small non-metallic  
brush.  
B
C
The two sprayer arms may both be removed.  
C
To remove the upper sprayer  
arm, rotate the locking ring in  
an anti-clockwise direction.  
The upper sprayer arm should  
be replaced with the holes  
facing upwards.  
1
2
A
The lower sprayer arm can be  
removed by pressing on the  
side tabs and pulling it  
upwards.  
4
3
After cleaning the filters, replace the filter assembly and  
fix it in position correctly; this is essential for maintaining  
the efficient operation of the dishwasher.  
Leaving the machine unused for extended periods  
•Disconnect the appliance from the electricity supply  
and shut off the water tap.  
Cleaning the water inlet filter*  
If the water hoses are new or have not been used for an  
extended period of time, let the water run to make sure it  
is clear and free of impurities before performing the  
necessary connections. If this precaution is not taken,  
•Leave the door of the appliance ajar.  
When you return, run a wash cycle when the  
dishwasher is empty.  
the water inlet could become blocked and damage the  
dishwasher.  
*Only available in selected models.  
11  
 
Precautions and advice  
The appliance was designed and manufactured  
Disposal of old electrical appliances  
EN  
in compliance with current international safety  
standards. The following information has been  
provided for safety reasons and should therefore be  
read carefully.  
The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment (WEEE),  
requires that old household electrical appliances  
must not be disposed of in the normal unsorted  
municipal waste stream. Old appliances must be  
collected separately in order to optimise the  
recovery and recycling of the materials they contain  
and reduce the impact on human health and the  
environment. The crossed out "wheeled bin" symbol  
on the product reminds you of your obligation, that  
when you dispose of the appliance it must be  
separately collected.  
General safety  
The appliance was designed for domestic use  
inside the home and is not intended for  
commercial or industrial use.  
The appliance must be used by adults only, to  
wash domestic crockery according to the  
instructions in this manual.  
The appliance must not be installed outdoors,  
even in covered areas. It is extremely dangerous  
to leave the machine exposed to rain and storms.  
Do not touch the appliance when barefoot.  
When unplugging the appliance always pull the  
plug from the mains socket, do not pull on the  
cable.  
Consumers should contact their local authority or  
retailer for information concerning the correct disposal  
of their old appliance.  
Saving energy and respecting the  
environment  
The water supply tap must be shut off and the  
plug should be removed from the electrical  
socket before cleaning the appliance or carrying  
out any maintenance work.  
Saving water and energy  
If the appliance breaks down, do not under any  
circumstances touch the internal parts in an  
attempt to carry out the repair work yourself.  
Never touch the heating element.  
Only start a wash cycle when the dishwasher is  
full. While waiting for the dishwasher to be filled,  
prevent unpleasant odours with the Soak cycle  
(see Wash Cycles).  
Do not lean or sit on the open door of the  
appliance: this may cause the appliance to  
overturn.  
Select a wash cycle that is suited to the type of  
crockery and to the soil level of the crockery using  
the Wash cycle table:  
The door should not be left open as it may create  
a dangerous obstacle.  
- for dishes with a normal soil level, use the Eco  
wash cycle, which guarantees low energy and  
water consumption levels.  
The packaging material should not be used as a  
toy: it can become a choking or suffocation  
hazard.  
- if the load is smaller than usual activate the Half  
load option* (see Start-up and use).  
If your electricity supply contract gives details of  
electricity saving time bands, run wash cycles  
during the periods when a lower tariff is applied.  
The Delayed start* button (see Start-up and use)  
helps you organise the wash cycles accordingly.  
If your family includes children:  
• DO NOT allow children to play with the appliance  
or tamper with its controls.  
• Keep detergents and rinse aids away from  
children.  
• Keep children away from the open door of a  
dishwasher, there could still be some detergent left  
inside.  
* Only available in selected models.  
12  
 
Phosphate-free and chlorine-free detergents  
containing enzymes  
EN  
We strongly recommend that you use detergents  
that do not contain phosphates or chlorine, as  
these products are harmful to the environment.  
Enzymes provide a particularly effective action at  
temperatures around 50°C, and as a result  
detergents containing enzymes can be used in  
conjunction with low-temperature wash cycles in  
order to achieve the same results as a normal 65°C  
wash cycle.  
To avoid wasting detergent, use the product in  
appropriate quantities based on the manufacturer’s  
recommendations, the hardness of the water and  
the soil level and quantity of the crockery. Even if  
they are biodegradable, detergents contain  
substances that may alter the balance of nature.  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping  
the environment, Hotpoint reserves the right to use  
quality recycled components to keep down customer  
costs and minimise material wastage.  
Please dispose of packaging and old appliances  
carefully.  
To minimise risk of injury to children, remove the door,  
plug and cut mains cable off flush with the appliance.  
Dispose of these parts separately to ensure that the  
appliance can no longer be plugged into a mains  
socket and the door cannot be locked shut.  
* Only available in selected models.  
13  
 
Troubleshooting  
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance  
EN  
(see Assistance).  
Malfunction:  
Possible causes / Solutions:  
The plug has not been inserted into the electrical socket properly, or  
The dishwasher does not start.  
there is no power in the house.  
The dishwasher door has not been shut properly.  
A delayed start has been programmed (see Start-up and use).  
The dishwasher cycle has not yet finished.  
No water drains out from the  
dishwasher.  
The water outlet hose is bent (see Installation).  
The drain duct is blocked.  
The filter is clogged up with food residues.  
The dishwasher makes  
excessive noise.  
The dishes are rattling against each other or against the sprayer  
arms.  
An excessive amount of foam has been produced: the detergent has  
not been measured out correctly or it is not suitable for use in  
dishwashers (see Start-up and use).  
The dishes and glasses are  
covered in a white film or  
limescale deposits.  
The level of the refined salt is low or the dosage setting is not  
suited to the hardness of the water (see Rinse aid and salt).  
The lid on the salt dispenser is not closed properly.  
The rinse aid has been used up or the dosage is too low.  
The crockery is made from non-stick material.  
The dishes and glasses are  
streaked or have a bluish  
tinge.  
The crockery has not been dried  
properly.  
The rinse aid dosage is too high.  
The rinse aid has been used up or the dosage is too low (see Rinse  
aid and salt).  
The rinse aid dispenser setting is not high enough.  
A wash cycle without a drying programme has been selected.  
The racks are overloaded (see Loading the racks).  
The crockery has not been arranged well.  
The dishes are not clean.  
The sprayer arms cannot move freely.  
The wash cycle is too gentle (see Wash cycles).  
An excessive amount of foam has been produced: the detergent has  
not been measured out correctly or it is not suitable for use in  
dishwashers (see Start-up and use).  
The lid on the rinse aid compartment has not been shut correctly.  
The filter is dirty or blocked (see Care and maintenance).  
The refined salt level is low (see Rinse aid and salt).  
There is no water in the mains supply.  
No water enters the  
dishwasher/Shut off tap alarm.  
(several short beeps are emitted)  
The water inlet hose is bent (see Installation).  
Turn on the tap and the appliance will start after a few minutes.  
(the 2 (Normal) and 3 (Soak) WASH  
CYCLES indicator lights flash).  
The appliance lock has been activated because no action was taken  
when the beeps sounded. Switch off the machine, using the ON/OFF  
button, turn on the tap and switch the machine back on after 20  
seconds by pressing the same button. Re-programme the machine  
and restart the wash cycle.  
Water loading solenoid valve  
malfunction alarm  
(the 2 (Normal) WASH CYCLE  
indicator lights flash).  
Switch off the machine by pressing the ON/OFF button and switch it  
back on after a minute. If the alarm continues, turn off the water tap  
to reduce the risk of flooding, remove the plug from the electrical  
socket and call Assistance.  
Water inlet hose alarm/Water inlet  
filter blocked.  
(the 1 (Intensive), the 2 (Normal) and  
the 3 (Soak) WASH CYCLES  
indicator lights flash).  
Switch off the appliance by pressing the ON/OFF button. Shut off  
the water tap to eliminate the risk of flooding and remove the plug  
from the electrical socket.  
Make sure the water inlet filter has not become blocked by various  
impurities. (see Care and maintenancechapter).  
14  
 
After Sales Service  
After Sales Service  
Appliance Registration  
EN  
No one is better placed to care for your Hotpoint  
appliance during the course of its working life  
than us - the manufacturer.  
We want to give you additional benefits of Hotpoint  
ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
UK: 0870 6092094  
Republic of Ireland: 01 230 0800  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering  
you access to 400 skilled telephone advisors and  
1100 fully qualified engineers on call to ensure you  
receive fast, reliable, local service.  
Indesit Company UK Ltd. Morley Way,  
Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial  
Estate,Dublin 17  
UK: 08709 066 066  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following  
information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts  
as well as accessory products that protect and  
hygienically clean your appliance to keep it looking  
good and functioning efficiently throughout its life.  
UK: 08709 077 077  
Republic of Ireland: 0818 313 413  
15  
 
Guarantee  
195062938.03  
06/2008- Xerox Business Services  
12 Months Parts and Labour Guarantee  
5 Year Parts Guarantee  
EN  
Your appliance has the benefit of our manufacturer’s  
guarantee, which covers the cost of breakdown  
repairs for twelve months from the date of purchase.  
Hotpoint also offers you a free 5 year parts  
guarantee. This additional guarantee is conditional  
on you registering your appliance with us and the  
parts being fitted by one of our authorised  
engineers. There will be a charge for our engineer's  
time. To activate the extra parts warranty on your  
appliance, simply call our registration line on 0870  
6092094 (ROI 01 230 0800).  
This gives you the reassurance that if, within that  
time, your appliance is proven to be defective  
because of either workmanship or materials, we will,  
at our discretion, either repair or replace the  
appliance at no cost to you.  
Extended Guarantees  
We offer a selection of repair protection plans that  
enable you to fully cover yourself against the  
expense of repair bills for the life of your policy. To  
find the ideal plan for you please call our advice line  
on 08709 088 088 (ROI 01 230 0233).  
Guarantee terms and conditions  
This guarantee is subject to the following conditions:  
- The appliance has been installed and operated  
correctly and in accordance with our  
operating and maintenance instructions.  
- The appliance is used only on the electricity or gas  
supply printed on the rating plate.  
Free Helpdesk Service  
- The appliance has been used for normal domestic  
purposes only.  
We have a dedicated team who can provide free  
advice and assistance with your appliance if you  
experience any technical difficulties within the first  
90 days of ownership. Simply call our Hotpoint  
Service Hotline on 08709 066 066 (ROI 0818 313  
413) for telephone assistance, or, where necessary,  
to arrange for an engineer to call. If we cannot  
resolve the technical problem we will replace your  
machine or, if you prefer, give you your money back.  
- The appliance has not been altered, serviced,  
maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
The guarantee does not cover:  
- Damage resulting from transportation, improper  
use, neglect or interference or as a result of  
improper installation.  
- Replacement of any consumable item or  
accessory.These include but are not limited to:  
plugs,cables, batteries, light bulbs, fluorescent  
tubes and starters, covers and filters.  
- Replacement of any removable parts made of  
glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE  
APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
16  
 

Graco Water Pump 309250t User Manual
Grizzly Saw G1572 User Manual
Hans Grohe Plumbing Product 06128XX0 User Manual
Havis Shields Automobile Accessories C TM IMP 1 User Manual
Hotpoint Dishwasher DF55 User Manual
HP Hewlett Packard Fan 403349 003 User Manual
HP Hewlett Packard Personal Computer B2B97UT#ABA User Manual
HP Hewlett Packard Server RP4410 User Manual
Husqvarna Blower 225B User Manual
Impex Home Gym MACH V User Manual