Honeywell Smoke Alarm IPGSM DPC User Manual

IPGSM-DPC  
Commercial Fire Communicator  
Installation and Setup Guide  
IPGSM-DPC Commer  
cial Fire Comm  
unicator  
RADIO  
TR  
OUBLE  
LO  
W
B
A
TT  
A
A
C
C
LOSS  
ON  
800-09370 6/11 Rev. A  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
General Information  
The IPGSM-DPC Commercial Fire Communicator (henceforth referred to as IPGSM-DPC) includes  
everything you need to upgrade a commercial fire system that previously reported by POTS to a system that  
uses the Internet as its primary reporting path, and uses a GSM cellular reporting path as a backup. In  
addition, this communicator utilizes a sophisticated power module (PowerBoost1) that monitors and reports  
AC power loss, low battery, and missing battery conditions.  
Package Contents  
Red Fire Cabinet and Back Plate Antenna and Mounting Adapter  
Mounting Rails (for above)  
Hardware Bag  
Cam Lock with Key  
PowerBoost1  
Dialer Capture Module  
iGSM Communications Module  
50 ohm cable assembly  
Battery harness/fuse (# 100-02415)  
Ferrite Filter  
LED Display board  
Transformer, 18VAC  
(# 1451-UL9)  
Compatible Fire Panels  
The IPGSM-DPC works with:  
All Fire Panels that are listed in the table below.  
All Fire Panels that use the Contact ID communication format as described in the SIA DC-05  
Standard.  
IMPORTANT: For a fire panel that has more than 9 active partitions, the first 9 partitions are  
reported to the central station uniquely. Beyond 9 partitions, only the 2nd digit of the partition is  
reported along with a leading zero (example partition 14 is reported as 04). The installer must  
inform the central station of this condition.  
The IPGSM-DPC is compatible with the Honeywell brand FACP’s listed below when the model  
659EN Line Fault Monitor is installed.  
Honeywell Fire Panel  
411  
Communicator  
family two  
Honeywell Fire Panel  
Communicator  
MS-9600LSC-FR  
family three  
Use the DACT-UD2 product to  
interface the IPGSM-DPC.  
411UD  
family two  
411UDAC  
family two  
NFS2-3030  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family one (requires UDACT)  
family four  
FireWarden-100-2C  
FireWarden-100-2C-FR  
FireWarden-50C  
FireWarden-50C-FR  
MS-10UD-7C  
family three  
NFS2-3030-FR  
NFS2-640  
family three  
family two  
NFS2-640-FR  
NFS-320  
family two  
family three  
NFS-320C  
MS-10UD-7C-FR  
MS-25C  
family one (requires UDACT)  
family four  
NFS-320C-FR  
NFS-320SYS  
NFS-320SYS-FR  
NSP-25C  
MS-5UD-7C  
family three  
MS-5UD-7C-FR  
MS-9050UDC  
MS-9050UDC-FR  
MS-9200UDLSC  
MS-9200UDLSC-FR  
MS-9600LSC  
family one (requires UDACT)  
family two  
SFP-10UDC  
SFP-10UDC-FR  
SFP-5UDC  
family three  
family two  
family three  
family three  
family three  
family three  
SFP-5UDC-FR  
family three  
family three  
Use the DACT-UD2 product to  
interface the IPGSM-DPC.  
1 –  
 
     
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
Operation  
The IPGSM-DPC replaces the fire panel's POTS communications path. When an event occurs, the fire panel  
goes off-hook to dial the central station. The IPGSM-DPC detects the off-hook condition and provides the  
fire panel with a dial tone. When the fire panel detects the dial tone, it begins dialing the central station.  
The IPGSM-DPC considers the three second period after dialing as the number dialing has been completed.  
After the dialing is completed, the Dialer Capture Module returns a handshake to the fire panel.  
The fire panel then sends the contact ID reports to the IPGSM-DPC, which in turn sends a kiss-off after the  
report is successfully received from the fire panel. Within the IPGSM-DPC, the Dialer Capture Module  
sends the contact ID reports over the ECP bus to the iGSM Communications Module. When all the reports  
are sent, the fire panel goes on-hook. The IPGSM-DPC then transmits the messages to the central station  
(either over the internet or the GSM network).  
2 –  
 
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
Installation  
ULC Compliance  
To meet Canadian ULC compliance, ensure the following:  
IPGSM-DPC must be installed in accordance with Canadian Electrical Code, Part 1.  
IPGSM-DPC must be mounted in the same room and within 20 feet of the fire panel. The wiring  
must be routed through conduit.  
IPGSM-DPC, and all equipment used for the IP connection (such as the router, hub, modem, etc.)  
shall be listed, must be powered from an un-switched branch circuit, and be provided with  
appropriate standby power.  
IPGSM-DPC must use a 7AH battery (not supplied) to provide 24-hour backup capability.  
STEP 1 – Setup the Customer Account  
The communicator requires a subscriber account (customer account) to be setup with AlarmNet Direct. This  
is accomplished by registering the communicator's iGSM communications module with AlarmNet.  
Registering, enables the fire panel to send reports.  
To setup the customer account you will need to contact the central monitoring station to get account  
information, and have access to the AlarmNet Direct website. To access the AlarmNet Direct website visit –  
If you do not wish to use the AlarmNet Direct website, you may call AlarmNet to setup the account, just  
phone 800-222-6525, then select option 1.  
(Monday–Friday 8:00 am to 9:00 pm, Saturday 9:00 am to 5:30 pm EST)  
Have the following information ready:  
Primary City ID (two digits), obtained from your  
monitoring station.  
Primary Subscriber ID (four digits), obtained  
from your monitoring station.  
Primary Central Station ID (two digits), obtained  
from your monitoring station.  
Communication Module's MAC ID, and MAC  
CRC number located on outside of box, and  
inside of the module.  
Note: The SIM supplied for the IPGSM-DPC is already activated. Therefore no SIM  
activation is necessary.  
STEP 2 – Register the Communications Module with AlarmNet  
Registering the module activates the account with AlarmNet and enables the fire system's control panel to  
send reports. There are three methods that can be used to register the communications module.  
Register the module by logging into AlarmNet Direct and choosing “Show Programmed Devices  
GSM/I”. Search for the account using the Account Information or MAC ID. Under the “Actions”  
column, use the pulldown menu and choose Register. OR  
After the IPGSM-DPC is installed and programmed, you can register the module by clicking the  
Tamper Switch 3 times. OR  
After the IPGSM-DPC is installed and programmed, you can register the module using the 7720P  
Programming tool. Simply: Press [Shift ] then press []. Please wait for "Registration SUCCESS"  
message.  
3 –  
 
       
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
STEP 3 – Determine the Signal Strength and Select a Location  
IMPORTANT - Do Not mount this device outdoors.  
RF Exposure  
Warning – The antenna(s) used for this transmitter must be installed to provide a separation  
distance of at least 20 cm from all persons and must not be collocated or operating in con-  
junction with any other antenna or transmitter.  
When choosing a suitable mounting location, understand that signal strength is very important for proper  
operation. For most installations using the supplied antenna, mounting the unit as high as practical, and  
avoiding large metal components provides adequate signal strength for proper operation.  
In this procedure, you will use the iGSM Communications Module to determine signal strength in order to  
find a suitable mounting location.  
Note: Since the SIM is already activated, the RSSI signal strength indicators will indicate  
signal strength.  
1. You will need a fully charged 12V battery.  
2. Attach the Antenna (see illustration on page 6).  
3. Temporarily wire the battery's negative [–] terminal to TB1–4 on the iGSM communications module,  
then wire the battery's plus [+] terminal to TB1–2 on the communications module. Wait about one  
minute for the module to initialize.  
4. Position the assembly near a suitable mounting position and observe  
the RSSI display.  
3 BARS MIN.  
5. Look for a mounting position that yields at least 3 bars lit solid. Four  
R
Y
Y
G
G
G
or five bars are better.  
7845i-GSM-025-V0  
6. Verify the signal strength remains steady for a few minutes, then mark that mounting position.  
Disconnect the battery.  
STEP 4 – Mount and Wire  
For ULC compliant installations, refer to the topic on ULC Compliance in this manual.  
For Dry/Indoor use only.  
External cabinet wiring MUST be routed in conduit.  
This communicator comes partially assembled with all the components mounted except the Antenna, LED  
Display board, and PowerBoost1. To protect certain components on the PowerBoost1, it is shipped un-  
mounted but fully wired.  
Note: Refer to the diagram on page 6, and to the Wiring Diagram on the inside of the back cover of  
this manual for wiring and component identification.  
1. Remove knockouts from cabinet to accommodate the power input wires, and wiring to the control  
panel. (DO NOT REMOVE the two knockouts directly above the PowerBoost1 module.) Then mount  
the cabinet securely to the wall using 4 screws or bolts. Use mounting screws or bolts that are  
suitable for the material being anchored to.  
2. Ensure the cabinet door lock is installed.  
3. Install the two plastic mounting rails for the LED Display board. They simply snap into the back  
plate holes.  
4 –  
 
   
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
4. Connect the LED Display board to its connector, then slide the board into the mounting rails. (Refer  
to the “LED Display Information” topic if a wire is detached from its connector.)  
5. Carefully remove the packaging material that surrounds the PowerBoost1.  
6. Mount the PowerBoost1 on the three unused standoffs. Use the plastic screw (prevents shorting)  
to secure the upper right corner of the PowerBoost1 and the two metal screws and lock washers to  
fasten the left side of the circuit board. Ensure the lock washers are located between the circuit  
board and the head of the two metal screws.  
7. Use the 1451-UL9 Wired Transformer directly connected to un-switched facility power. Connect and  
route 14AWG (minimum) insulated wire from facility ground to the 1451-UL9 enclosure ground post  
and through the conduit to the IPGSM-DPC cabinet ground post.  
8. Route 16AWG wire from the transformer secondary, through the conduit. Pass the wires through  
the Ferrite Filter, then loop the wires back through again making a loop. (Ensure the wire ends that  
connect to the PowerBoost1 Module are tinned.) Connect the wires to the PowerBoost1 AC  
terminals. At this time DO NOT apply power.  
9. Ensure all ground connections are tight.  
10. Connect the Ethernet cable and the Telco 1 and Telco 2 lines. If you choose to use an optional  
Cabinet Tamper Switch (if the control panel supports it) mount and wire it.  
Note: The Ethernet cable, Telco 1, Telco 2 lines, and the optional cabinet Tamper Switch (if used)  
must be run through conduit.  
11. Verify the PowerBoost1 module DIP switches are configured as shown below.  
PowerBoost1  
ON  
1 2 3  
5
4
ON  
(Switch handle = white)  
1
2
3
4
5
12. Ensure the following:  
LED Display board is fully seated.  
All wiring terminals and connectors are tight.  
All wiring has been completed and secured with cable ties.  
13. Install the battery (not supplied). Apply power to the 1451-UL9 Wired Transformer, and attach the  
battery cable.  
5 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
ANTENNA  
1451-UL9 WIRED  
TRANSFORMER  
WIRES MUST BE  
RUN IN CONDUIT  
TO 24 HR  
NUT,  
WASHER  
BLU  
BLU  
FACILITY POWER  
120VAC, 60Hz, 850mA  
GND  
POST  
18 VAC  
72 VA  
ANTENNA  
MOUNTING  
ADAPTER  
GND  
BLU  
BLU  
TO Cabinet Ground Post  
TO PowerBoost1  
DO NOT REMOVE these knockouts.  
CABINET  
DOOR  
ON  
1
2
3
4
5
RED  
GREEN  
Dialer Capture Module  
FOR EXTERNAL ANTENNA  
50 OHM MMCX ONLY  
7720P PROGRAMMER PORT  
NOT FOR TELEPHONE SERVICE USE!  
PRIMARY POWER:  
CURRENT: 900mA PEAK, 70mA STANDBY  
BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP  
9
-
16.5 VAC  
BATTERY  
TO Facility  
Ground  
FCC:XXXXXXXXXX IC: YYYYYYYYYY  
TB 1  
1
2
3
4
5
6
7
8
9
FUSE  
PN: 100-02415  
+
10  
11  
CONDUIT  
BATTERY  
7AH  
(not supplied)  
iGSM Comm Module  
Wiring for Grounds, Power, and RF  
6 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
Wiring the 659EN Line Fault Monitor (if required)  
The IPGSM-DPC is compatible with the Honeywell brand FACP’s listed on page 1 when the model 659EN  
Line Fault Monitor is installed.  
1. Refer to the installation guide for the 659EN.  
2. Mount the 659EN on the lower left side of the IPGSM-DPC cabinet.  
3. DO NOT cut the 659EN’s BLACK Output Relay Jumper or the BLUE Voltage Trip Threshold  
Jumper.  
4. Complete the interface wiring as shown below:  
to Dialer Capture Module, Terminal, Tip 2  
to Dialer Capture Module, Terminal, Ring 2  
to Power Boost 1, Terminal, OUTPUT 1, DC+  
to Power Boost 1, Terminal, OUTPUT 1, DC-  
to Power Boost 1, Terminal, ERTH GND  
YEL  
ORG  
RED  
BLK  
GRN  
659EN  
Wire to a  
Zone on the Fire Panel  
4.7K, 1/2 watt  
IPGSM-DPC  
Example wiring for an addressable fire control panel:  
FIRE LITE Addressable Fire Alarm Control Panel  
MS-9050UD  
IPGSM-DPC  
Commercial Fire Communicator  
- To next device  
+ on SLC Loop  
to Dialer Capture Module, Terminal, Tip 2  
to Dialer Capture Module, Terminal, Ring 2  
to Power Boost 1, Terminal, OUTPUT 1, DC+  
to Power Boost 1, Terminal, OUTPUT 1, DC-  
to Power Boost 1, Terminal, ERTH GND  
YEL  
ORG  
RED  
BLK  
GRN  
TOP  
MMF-300A  
Braided-shield/Drain  
Monitor Module  
Wire  
T11  
T10  
T9  
T8  
T7  
T6  
T1  
T2  
T3  
T4  
T5  
7
8
7
8
6
9
6
9
5
5
10  
11  
12  
13  
14  
4
3
4
3
2
2
1
1
0
0
15  
TENS  
ONES  
LOOP  
ADDRESS  
659EN  
4.7K, 1/2 watt  
B+  
TB2  
B-  
Shield  
TB5  
B+ A+ B- A-  
A
B
NO NC  
C
RELAY 1  
ALARM CONTACTS  
SLC Loop  
IPGSM-DPC-014-V0  
7 –  
 
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
STEP 5 – Program the Communications Module  
You must use the 7720P Programming tool to program the IPGSM-DPC.  
When using the 7720P Programming tool, the values given below are for most installations. Press the [#]  
key to accept the displayed default value (xxx) or enter the new value and press the [#] key for the next  
prompt. Use the [Space] key to scroll through a list of options.  
(no display)  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Connect the 7720P.  
7720P PROGRAMMER  
Strt Prog Mode? Y/N  
Program Device? Y/N  
Com Path Choice (IP&GSM)  
Primary City ID (??)  
Press [#].  
Press [Shift] then [Y], then [#].  
Press [Shift] then [Y], then [#].  
Press [Space] to scroll choices; IP&GSM, IP, or GSM. At choice, press [#].  
Enter number 01-99, then press [#].  
Enter number 01-FE, then press [#].  
Enter number 0001-9999, then press [#].  
Primary CS ID (??)  
Primary Sub ID (????)  
Note: If a Com Path Choice of IP&GSM or IP was selected, prompt 9 will  
appear.  
Use DHCP? Y/N (Y)  
9.  
If your router is configured for DHCP, press [Shift] then [Y], then press [#].  
Note: If DHCP is not selected (your router is set for a static IP), prompts 10  
through 13 will appear.  
NIC IP Address:  
255.255.255.255  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
Enter choice, then press [#]. Follow the prompts.  
Enter choice, then press [#]. Follow the prompts.  
Enter choice, then press [#]. Follow the prompts.  
Enter choice, then press [#]. Follow the prompts.  
Enter choice, then press [#]. Follow the prompts.  
Enter choice, then press [#]. Follow the prompts.  
Press [Shift] then [Y], then press [#].  
Subnet Mask:  
255.255.255.255  
Gateway IP Address:  
255.255.255.255  
DNS Serv IP Addr:  
255.255.255.255  
Review? Y/N  
Create Password? Y/N  
Exit Prog Mode? Y/N  
DONE  
Notes: If an error in programming occurs, set the factory defaults (see next topic) and reprogram.  
The IP Fault Time, and the GSM Fault Time are each fixed at 1 minute and are not  
programmable.  
8 –  
 
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
To exit the programming mode, press [N] in response to the "Review?" prompt. Then press [Y] to the "Exit  
Prog Mode?" prompt. Upon exiting, the root file is updated to log the changes made. A message is displayed  
telling the user that this step is being executed. When complete, the message "DONE" is displayed to  
indicate the file was successfully uploaded.  
Note: If critical configuration changes were made, such as the mode of operation, the  
communications module will reset to ensure that the programming features are enabled.  
If the file is not successfully uploaded, one of the following prompts will be displayed. Follow the steps  
shown below until the upload is successful.  
Display  
Description  
What to do  
Module is not yet initialized.  
Wait for RSSI indicator LEDs to be lit.  
Press [Y].  
Cannot Upload  
Try Again? Y/N_  
Network problem, or you answered "N"  
to "Cannot Upload Try Again?" prompt.  
Initiate the Force Server Update  
Command by pressing the [0] key.  
Failed to Update  
Root File!  
Setting Factory Defaults  
To reset the programming options to factory-default values, at the "Exit Prog Mode?" prompt press [Shift]  
plus [ESC]. Note, setting the factory defaults will also erase any password that may have been entered.  
Press [Y] to reset factory default values.  
Press [N] to cancel this function.  
Set Default?  
Y/N_  
Press [Shift] then [Y], then [#]. The Create Password prompt appears, follow the prompts then exit.  
STEP 6 – Configure the Fire Panel  
1. Ensure the Telco Fault on the panel is enabled. Then choose a setting that is no higher than 90  
seconds (or as close to that as the panel allows).  
2. Ensure no more than 1 pause character (usually a comma) is programmed into the dialing string  
(usually 2 seconds). Note, this is necessary since the Dialer Capture Module waits only 3 seconds  
after the phone number is dialed. Having more than 3 seconds of pause time will cause it to think  
the phone number is complete and cause it to generate the high-low tones at an incorrect moment.  
STEP 7 – Test the System  
1. Close and lock the cabinet cover.  
2. Refer to the fire panel's installation/operation guide for the testing procedure.  
3. (Notify the monitoring station that a test will be conducted.) Test the system to ensure it is  
operating.  
4. Verify communications with the central station is successful by sending several events. Also, get  
confirmation that these events were received.  
9 –  
 
   
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
Dialer Capture Module Information  
LED Indicator  
STATUS  
RED – Steady ON  
Messages exist in buffer.  
RED – Flashing  
No messages to be sent. Waiting for messages.  
Normal Indication.  
GREEN – Steady ON  
GREEN – Blinks every 2 sec.  
GREEN – Blinks twice every sec.  
GREEN – Blinks 10 times every sec.  
PowerBoost1 communication problem.  
Communication Module connection is lost.  
PowerBoost1 and Communications Module connection is lost.  
Note: Telco ports 1 (primary dialer)  
and 2 (secondary dialer) may be  
used instead of the terminal board.  
Whichever connection method is  
used, both Telco paths must be  
connected to the Fire Panel.  
RED  
GREEN  
Dialer Capture Module  
LED Display Information  
Panel Status  
LED Indicator  
RADIO TROUBLE  
Yellow – ON when radio trouble is present.  
Both IP and GSM communication paths are lost.  
Communicator radio is not registered.  
RADIO TROUBLE  
Old Alarm Time has been exceeded. (Message has not been  
delivered within the fixed 10 minute window.)  
Buzzer – Upon loss of AC power, this will beep once every 10  
seconds.  
LOW BATTERY  
(not used)  
AC LOSS  
LOW BATTERY  
Yellow – ON when battery is low (<11.5VDC).  
Yellow – (not used)  
AC ON  
AC LOSS  
AC ON  
Yellow – ON when no AC is present (< 90VAC).  
Green – ON when AC is present.  
Violet  
Black  
White  
Note: If a wire pulled out of the LED Board Connector  
refer to the diagram on right and reinsert wire, ensuring  
the connector pin is locked in.  
LED Board  
Connector  
Wires  
NC  
NC  
Red  
Brown  
Yellow  
Gray  
10 –  
 
   
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
PowerBoost1 Module Information  
LED Indicator  
AC (green)  
STATUS  
AC power available.  
ACTIVE (green)  
Cyclical flashing – normal communications.  
Repetition of 3 flashes – loss of communications.  
LOW BATT (yellow)  
TROUBLE (yellow)  
Missing or low battery.  
One or more trouble conditions exist, such as; overload, output supervision,  
ground fault, or charger failure.  
Notes:  
If AC power is lost and the battery voltage falls below 10v, the module's output voltage will be  
turned off. The output power is turned back on when AC power is restored.  
You must use the DIP switch settings shown below.  
PowerBoost1  
LOW BATT LED  
INDICATOR  
TROUBLE LED  
INDICATOR  
Confiure DIP switch  
ON  
as shown:  
1
2
3
4
5
ON  
1 2 3  
5
4
(Switch handle = white)  
AC LED  
INDICATOR  
ACTIVE LED  
INDICATOR  
iPGSM-COM-003-V0  
11 –  
 
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
iGSM Communications Module Information  
ON NOT registered with AlarmNet.  
OFF – Registered with AlarmNet.  
FAST BLINK – Download session with Compass  
in progress.  
GRN  
SLOW BLINK – In unison with yellow LED,  
registration in progress.  
PRIMARY POWER: 9 - 16.5 VAC  
CURRENT: 900mA PEAK, 70mA STANDBY  
BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP  
7720P  
Programmer  
Port  
FCC:XXXXXXXXXX IC: YYYYYYYYYY  
ON – Message transmission pending.  
QUICK PERIODIC BLINK – Normal.  
FAST BLINK – Message waiting for network ACK.  
SLOW BLINK – Idle power abnormal.  
SLOW BLINK – In unison with green LED,  
registratration in progress.  
YEL  
RED  
TB 1  
1
2
3
4
5
6
7
8
RSSI / Mode  
and  
status LEDs  
Tamper  
Switch  
ON No contact with network.  
OFF – Normal.  
SLOW BLINK – Loss of communication with the  
Dialer Capture Module (ECP fault).  
Mode  
Switch  
9
10  
11  
FAST BLINK – No network contact AND loss of communi-  
cation with the Dialer Capture Module  
.
Note: If all LEDs FAST BLINK in unison with  
the RSSI LEDs this indicates a Hardware Error.  
ON – 100 MB/S link to Internet.  
OFF – 10 MB/S link to Internet.  
Link Speed  
GREEN  
ON – Ethernet Link detected.  
OFF – No link detected.  
FAST BLINK – Transmitting/Receiving Data.  
Ethernet Link/Activity  
GREEN  
MODULE'S RECEIVED SIGNAL STRENGTH (RSSI)  
When the Mode Switch is NOT depressed, LED 1 will illuminate red.  
The remaining LEDs indicate RSSI (Received Signal Strength).  
MODULE'S OPERATION MODE  
When the Mode Switch IS depressed, LED 1 will be OFF.  
LEDs 2 and 3 indicate the module's communication mode with the Dialer Capture Module.  
Mode  
LED 2 (yellow)  
LED 3 (yellow)  
OFF  
ON  
OFF  
OFF  
ON  
ECP  
Zone (NOT USED)  
4204 (NOT USED)  
2 - 4204 (NOT USED)  
OFF  
ON  
ON  
MODULE'S STATUS  
When the Mode Switch IS depressed, LED 1 will be OFF.  
LEDs 4, 5, and 6 indicate the module's Status.  
LED 4 (green)  
LED 5 (green)  
LED 6 (green)  
ON - Connected to  
ON - GPRS service  
available.  
ON - Module registered, no second  
site available.  
Internet.  
OFF - Not connected  
OFF - No GPRS service OFF - Module not registered with  
available network carrier.  
to Internet.  
FAST BLINK - GPRS in SLOW BLINK - Module registered, second  
use.  
site available, and low signal strength.  
NORMAL BLINK - Module registered, second  
site available, acceptable signal strength.  
FAST BLINK - Module registered, second  
site available, excellent signal strength.  
12 –  
 
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
RF Specifications  
Transmission  
Frequency  
Transmit  
Power  
Receive  
Frequency  
Receive  
Sensitivity  
(dBm)  
Number  
of  
Channels  
Channel  
Spacing  
(MHz)  
Duplex  
Separation  
Band  
(MHz)  
(dBm)  
(MHz)  
(kHz)  
GSM 850  
GSM 900  
GSM 1800  
GSM 1900  
824-849  
890-915  
33  
33  
30  
30  
869-894  
935-960  
-107  
-107  
124  
124  
374  
299  
200  
200  
200  
200  
45  
45  
95  
80  
1710-1785  
1850-1910  
1805-1880  
1930-1990  
-106  
-105.5  
Central Station Messages  
Alarm Condition  
Power On / Reset  
Alarm Code  
Restore Code  
E339 C0803  
E337 C0803  
E338 C0803  
E314 C0803  
E355 C0000  
E350 C0951  
E350 C0952  
E358 C0803  
5555 5555 9  
N/A  
Power Loss  
R337 C0803  
R338 C0803  
R314 C0803  
R355 C0000  
R350 C0951  
R350 C0952  
R358 C0803  
N/A  
Low Battery  
Battery Charger Failure  
ECP Supervision (Compromise Indication)  
Primary Communication Path Supervision  
Secondary Communication Path Supervision  
Periodic Comm Test Fail  
Test  
Specific to RESIDENTIAL / COMMERCIAL Control Panels (Such as the VISTA-10P, 15P,  
and 20P series.)  
UL: The information provided in this section for the VISTA-10P, 15P, and 20P series control  
panels has not been evaluated with this communications module.  
Communicator Trouble (low battery, ECP bus,  
network) (Possible Compromise Indication)  
E353 C0803  
R353 C0803  
R353 C0103  
Radio Fault  
E353 C0103  
Specific to COMMERCIAL Control Panels (Such as the VISTA-128/250 series.)  
Communicator Trouble (low battery, ECP bus,  
network) (Possible Compromise Indication)  
E333 C0803  
E357 C0803  
E333 C0803  
R333 C0803  
Radio Loss of Signal  
(Possible Compromise Indication)  
R357 C0803 or  
R380 C0803  
Radio Fault (low battery, tamper, ECP Bus)  
R333 C0803  
AlarmNet Messages  
Communication failure.  
5555 1555 6  
5555 3555 6  
(Possible Compromise Indication)  
Authorized Radio Substitution  
Unauthorized Radio Substitution Attempt  
Service Termination  
00D0 010C 0  
00D0 010E 0  
00D0 020E 0  
N/A  
N/A  
N/A  
13 –  
 
   
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
IPGSM-DPC Trouble Detection Information  
Telco 1 is used for the Fire Panel to output contact ID messages to the IPGSM-DPC, and Telco 2 is used by  
the IPGSM-DPC to report faults to the Fire Panel. If Telco 1 is not operational, the Fire Panel will use Telco  
2 to report events if there are no faults in the iGSM Communications module.  
Fault Condition  
Indication to Fire Panel  
PowerBoost1 fault  
Telco 2 is cut.  
iGSM Communications Module fault  
Telco 2 is cut.  
Failure of the communications path when  
IP only or GSM only is programmed as a  
communications path.  
Telco 1 and 2 are cut.  
Failure of both communications paths  
when IP&GSM is programmed as a  
communications path.  
Dialer Capture Module buffer is full.  
Hang up. (Panel will retry, giving the buffer a chance to  
empty.)  
IPGSM-DPC Specifications  
ITEM  
SPECIFICATION  
Width = 12 3/4 inches  
Cabinet Dimensions:  
Height = 14 7/8 inches  
Depth = 3 inches  
Primary – 120VAC, 60Hz, 850mA  
Secondary – 18VAC, 72VA  
Transformer: 1451-UL9  
12V, 7Ah sealed lead acid type (not supplied)  
Battery:  
Use a Honeywell 712BNP, Yuasa NP7-12 or equivalent.  
maximum 1A  
Battery Charging Current:  
Supervision:  
The Radio (communicator), battery, and AC power, conditions are  
monitored by the cabinet indicator LEDs:  
RADIO TROUBLE lights when any of these conditions exist.  
Both IP and GSM communication paths are lost.  
Communicator radio is not registered.  
Old Alarm Time has been exceeded. (Message has not been  
delivered within the fixed 10 minute window.)  
LOW BATTERY lights when the battery voltage is less than 11.5VDC.  
AC LOSS lights when the AC power is less than 90VAC.  
14 –  
 
   
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
15 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
16 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
17 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
18 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
19 –  
 
IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide  
NOTES  
20 –  
 
Wiring Diagram  
The wiring diagram below is depicted for point-to-point electrical connection checks used for troubleshooting  
or component replacement. It is not intended to show the physical routing of wires. When replacing a wire  
or component, ensure the wire is routed in the same manner as the original factory wire.  
1451-UL9 WIRED  
TRANSFORMER  
ANTENNA  
WIRES MUST BE  
RUN IN CONDUIT  
TO 24 HR  
FACILITY POWER  
BLU  
BLU  
120VAC, 60Hz, 850mA  
18 VAC  
72 VA  
GND  
POST  
TO Cabinet Ground Post  
GND  
BLU  
BLU  
TO PowerBoost1  
DO NOT REMOVE these knockouts.  
(Buzzer)  
OPTIONAL CABINET  
TAMPER SWITCH  
WHT (LO BATT)  
CABINET  
DOOR  
LED Display  
RADIO  
TROUBLE  
PowerBoost1  
Buzzer  
TROUBLE  
LOW  
BATT  
VIO  
BLK  
WHT  
RED  
BRN  
YEL  
GRA  
LOW BATT  
(not used)  
AC LOSS  
AC ON  
ON  
1
2
3
4
5
RED  
GREEN  
Dialer Capture Module  
AC  
ERTH GND  
GND  
TX  
BLK  
GRN  
(RADIO TROUBLE)  
RX  
YEL  
OUT+  
DC+  
OUT-  
DC-  
RED  
RED  
BLK  
N/U  
OUT+  
DC+  
OUT-  
DC-  
N/U  
iGSM Comm  
Module  
(AC ON)  
GRA  
STATUS  
MESSAGE  
FAULT  
FOR EXTERNAL ANTENNA  
50 OHM MMCX ONLY  
BATTERY  
7720P PROGRAMMER PORT  
NOT FOR TELEPHONE SERVICE USE!  
FUSE  
7720P  
PRIMARY POWER:  
9
-
16.5 VAC  
CURRENT: 900mA PEAK, 70mA STANDBY  
BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP  
PROGRAMMER  
PORT  
PN: 100-02415  
FCC:XXXXXXXXXX IC: YYYYYYYYYY  
TB 1  
1
2
3
4
+
RSSI/MODE  
INDICATORS  
+12V In  
GND  
ECP In  
ECP Out  
5
6
7
8
MODE & STATUS  
SWITCH  
BATTERY  
TAMPER  
SWITCH  
7AH  
(not supplied)  
9
10  
INTERNET  
CONNECTIVITY  
INDICATORS  
Use a Honeywell 712BNP,  
Yuasa NP7-12, or equivalent.  
11 FLT Out  
CONDUIT  
To Router  
To Fire Panel  
To Fire Panel  
NOTES All circuits are power limited except the backup battery which is non-power limited.  
Non-power limited wiring must be separated from the power limited wiring by at least 1/4 inch.  
If desired, use a Honeywell 955WH Tamper Switch with the 28-2 bracket.  
 
IC STATEMENT  
Notice: This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.  
IC STATEMENT  
This device complies with RSS 210 of IC. Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference. (2) This device must accept any interference received,  
including interference that may cause undesired operation.  
Cet appareil est conforme à la RSS 210 des Industries Canada. Son fonctionnement est soumis aux  
conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit  
accepter toute interference reçue y compris les interferences causant une reception indésirable.  
DOCUMENTATION AND ONLINE SUPPORT  
For the latest documentation and online support information, please go to:  
WARRANTY  
For the latest warranty information, please go to:  
2 Corporate Center Drive, Suite 100,  
P.O. Box 9040, Melville, NY 11747  
Copyright 2011 Honeywell International Inc.  
Ê800-093708Š  
800-09370 6/11 Rev. A  
 

Grace Turntable GDI VW00 User Manual
Graco Heat Pump 218747 User Manual
Graco Stroller PD210478B User Manual
Grizzly Lathe G97030 User Manual
Halo Lighting System Indoor Furnishings S1S EX User Manual
Hamilton Beach Juicer 67801 User Manual
Hotpoint Refrigerator FTM70S User Manual
HP Hewlett Packard Network Router CFL 512 User Manual
Hsu Research Speaker STF User Manual
IBM Printer LaserJet 5500 User Manual