Harbor Freight Tools Work Light 98085 User Manual

36 led solar  
security light  
Model 98085  
asseMbly and operation instructions  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
distributed exclusively by harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
saVe this Manual.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
inattention while operating the Solar  
Security Light may result in serious  
personal injury.  
grounded. Ground Fault Circuit Inter-  
rupter (GFCI) should also be imple-  
mented – it prevents sustained elec-  
trical shock.  
2. Use the Solar Security Light only with  
specifically designated battery packs.  
Use of any other battery packs may  
create a risk of injury and fire.  
general safety  
1. Do not use Solar Security Light for  
other than intended use.  
3. When battery pack is not in use, keep  
it away from other metal objects, like  
paper clips, coins, keys, nails, screws  
or other small metal objects, that can  
make a connection from one terminal  
to another. Shorting the battery termi-  
nals together may cause burns or a  
fire.  
2. Inspect before use. Do not use if  
parts are loose or damaged. Main-  
tain labels and nameplates on the  
Solar Security Light. These carry  
important safety information. If un-  
readable or missing, contact Harbor  
Freight Tools for a replacement.  
4. Ni-Cd batteries must be recycled or  
disposed of properly. Do not inciner-  
ate.  
3. The warnings, precautions, and in-  
structions discussed in this instruction  
manual cannot cover all possible con-  
ditions and situations that may occur.  
It must be understood by the operator  
that common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
5. Install Ni-Cd batteries only.  
6. Under abusive conditions, liquid may  
be ejected from the battery; avoid  
contact. If contact accidentally oc-  
curs, flush with water. If liquid con-  
tacts eyes, additionally seek medical  
help. Liquid ejected from the battery  
may cause irritation or burns.  
saVe these  
instructions.  
7. This product is not a toy. Keep it out  
of reach of children.  
8. People with pacemakers should  
consult their physician(s) before use.  
Electromagnetic fields in close prox-  
imity to heart pacemaker could cause  
pacemaker interference or pacemak-  
er failure. In addition, people with  
pacemakers should:  
• Avoid operating alone.  
• Do not use with power switch locked  
on.  
• Properly maintain and inspect to  
avoid electrical shock.  
• Any power cord must be properly  
SKU 98085  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
Panel (2) can be installed only as far  
apart as the connecting wire allows.  
speciFications  
Charge Time 6-8 hours  
4. Choose a location that receives full,  
direct sunlight a minimum of eight  
hours a day. The location should not  
be near nighttime light sources such  
as porch lights or streetlights as this  
will cause the Light to remain off.  
(5), 1.2V, 600 mAh/6V, Ni-Cd  
rechargeable battery pack  
Power Source  
Detects motion over a range of  
120° at 16 feet.  
Range  
Delay  
5-60 seconds  
Working  
Conditions  
14° - 131° F  
<80% RH  
5. During the day, the Solar Panel con-  
verts sunlight into electricity which  
recharges the batteries. The amount  
of light the Solar Panel receives  
unpacking  
depends on placement of the Light,  
geographic location and weather. If  
the weather is cloudy and the panel  
did not receive a full charge, the Light  
may not achieve full operating time.  
When unpacking, check to make sure  
that the item is intact and undamaged. If  
any parts are missing or broken, please  
call Harbor Freight Tools at the number  
shown on the cover of this manual as soon  
as possible.  
6. Mount the Lamp (1) on a solid sur-  
face capable of supporting the Lamp  
(1) and secure enough so that it will  
not move when exposed to vibration  
or wind.  
asseMbly  
read the entire iMportant  
saFeguards section at the  
beginning of this manual  
including all text under  
Figure 1  
subheadings therein before set  
up or use of this product.  
1. Note: For additional information  
regarding the parts listed in the fol-  
lowing pages, refer to the Assembly  
Diagram near the end of this manual.  
rear-  
mounting  
holes  
2. The Security Light should be set up  
at a location where you desire to  
have extra lighting to detect persons  
or objects moving at night or in the  
dark.  
inside-  
mounting  
holes  
3. Decide where you want to place the  
Lamp (1) and Solar Panel (2). The  
Light is equipped with a connect-  
ing wire, so the Lamp (1) and Solar  
7. To mount the Lamp (1), the Screws  
(5) can be inserted into either the  
rear mounting holes or to the inside  
mounting holes as shown in Fig. 1.  
If using the inside mounting holes,  
SKU 98085  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
remove the Covers (3) to allow for  
insertion of the Screws.  
operation  
read the entire iMportant  
saFeguards section at the  
beginning of this manual  
including all text under  
subheadings therein before set  
up or use of this product.  
8. Set the Lamp (1) to the angle height  
Drill holes for the enclosed screws.  
Make certain that the drilling path is  
clear of obstacles such as cables,  
gas and water pipes and electrical  
lines. Insert anchors into the holes.  
Thread in the enclosed Screws (5)  
to secure the Lamp (1) in position.  
note: No anchors are needed if unit  
is mounted on wall studs.  
Figure 2  
9. Before mounting the Panel, make  
certain that the connecting wire will  
reach both the Lamp (1) and Panel  
(2). Install the Solar Panel the same  
way that you installed the Lamp in  
step 8, using the mounting holes  
located on the base of the Panel.  
Insert Screws (4) through mounting  
holes in the base.  
On/Off Button  
Connecting  
Wire (8)  
1. Plug the Mounting Wire (8) into the  
Lamp as shown in Figure 2.  
2. Before it can operate to its full capac-  
ity, the Security Light needs to be in  
sunlight for two to three days. Turn  
the On/Off Button (see Figure 2) to  
the “OFF” position and wait two to  
three days before use.  
10. Adjust the Motion Detector Head be-  
low the light by moving it left or right  
so that it faces the area where move-  
ment will occur.  
3. Turn the switch to the “ON” position  
and wait about a minute. The light  
will turn itself on and then shut off  
three times to calibrate itself.  
4. Wait one minute after the self calibra-  
tion. The use the adjustment knob on  
the back of the motion sensor head to  
adjust the time that the light will stay  
on when the motion sensor detects  
movement.  
5. The light will turn on automatically at  
night when motion is detected by the  
Motion Detector Head.  
reV 08e  
SKU 98085  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
replacing the batteries  
inspection and  
Maintenance  
Figure 3  
to preVent  
serious injury  
FroM accidental  
Lamp  
Base  
Battery  
Pack  
operation or electric  
shock:  
Motion  
Detector  
Head  
before appliance inspection  
or maintenance, make sure  
the appliances switch is  
turned off, and the unit has  
cooled completely.  
1. The Battery Pack is located in the  
Base of the Lamp (1). Remove the  
screws that connect the base togeth-  
er. Separate the base as shown in  
Figure 3.  
to preVent serious  
injury FroM appliance  
Failure:  
do not use damaged  
products.  
2. Replace with a Ni-Cd battery pack of  
the same type.  
3. Connect base back together and at-  
tach to Lamp, making certain that the  
Motion Detector Head (see Figure  
3) is facing in the correct direction.  
Note: Be careful not to pinch wires  
when re-assembling.  
beFore each use, inspect  
the general condition of the  
Solar Security Light. Check for  
loose screws, misalignment or  
binding of moving parts, cracked  
or broken parts, and any other  
condition that may affect its safe  
operation.  
1. When storing your Light indoors for  
more than 2 or 3 days, turn the ON/  
OFF Power Switch to “OFF”.  
2. Store the Light in a dry location free  
of dust and debris. Make certain that  
the Light is out of reach of children.  
Storing the Light for prolonged pe-  
riods may damage the light or de-  
crease performance.  
3. Keep the Solar Panel free from dirt  
and debris. A dirty Solar Panel will  
keep the batteries from charging.  
Clean regularly with a damp cloth.  
SKU 98085  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
please read the FolloWing careFully  
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROVIDeD THe PARTS LIST AND ASSeMBLy DIAGRAM IN THIS MANUAL  
AS A ReFeReNCe TOOL ONLy. NeITHeR THe MANUFACTUReR OR DISTRIBUTOR MAKeS ANy RePReSeNTATION OR  
WARRANTy OF ANy KIND TO THe BUyeR THAT He OR SHe IS qUALIFIeD TO MAKe ANy RePAIRS TO THe PRODUCT,  
OR THAT He OR SHe IS qUALIFIeD TO RePLACe ANy PARTS OF THe PRODUCT. IN FACT, THe MANUFACTUReR AND/  
OR DISTRIBUTOR exPReSSLy STATeS THAT ALL RePAIRS AND PARTS RePLACeMeNTS SHOULD Be UNDeRTAKeN By  
CeRTIFIeD AND LICeNSeD TeCHNICIANS, AND NOT By THe BUyeR. THe BUyeR ASSUMeS ALL RISK AND LIABILITy  
ARISING OUT OF HIS OR HeR RePAIRS TO THe ORIGINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISING  
OUT OF HIS OR HeR INSTALLATION OF RePLACeMeNT PARTS THeReTO.  
parts list  
part  
description  
Q’ty  
1
2
3
4
5
6
7
8
Lamp - 36 LeD  
Solar Panel  
Cover  
Screw #6 x 1”  
Screw #6 x 1-9/16”  
Anchor  
Battery Pack  
Connecting Wire  
1
1
1
3
2
5
1
1
asseMbly diagraM  
1
2
7
3
8
5
4
6
SKU 98085  
For technical questions, please call 1-800-444-3353.  
Page 7  
 

Haier Washer XPB10 LAP User Manual
Hamilton Beach Toaster 31334 User Manual
Harbor Freight Tools Router 32650 User Manual
Havis Shields Window WGI F13 User Manual
Heath Zenith Home Safety Product SH 5316 User Manual
HP Hewlett Packard Switch FC 1GB 2GB SWITCH 16B User Manual
Humminbird Marine GPS System 4090501 User Manual
Husqvarna Lawn Mower 2754 GLS User Manual
IBM Blood Glucose Meter 5697 VM3 User Manual
Image Treadmill IMTL391052 User Manual