AB465A PCI-X
2-Port 2 Gigabit Fibre Channel and 2-Port
Gigabit Ethernet Combination Card Installation
Guide
For fcd Driver Versions B.11.11.04 and B11.23.02 and
For igelan Driver Versions B.11.11.17 and B.11.23.05
HP 9000 and HP Integrity Systems
Manufacturing Part Number : AB465-90001
E0205
U.S.A.
© Copyright 2005 Hewlett-Packard Development Company L.P.
Hardware and Software Installation Procedure
Step 1: Access the system card bay
Hardware and Software Installation Procedure
These instructions apply to AB465A PCI-X 2-Port 2 Gigabit Fibre Channel and 2-Port Gigabit Ethernet
combination cards which can operate on HP-UX 11i v 1.0 of December 2004 or HP-UX 11i v 2.0 of
September 2004 or later. If your system is running HP-UX 11i v 1.0, you can find the 11i v 1.0 LAN
and fibre channel driver bundles on the December 2004 OE distribution media. For 11i v 1.0, you
can either load the entire OE or just the two driver bundles for this card. If loading this product
on 11i v 2.0, you need to load the entire HP-UX 11i v 2.0 September 2004 OE from the distribution
media and you will automatically get the correct LAN and fibre channel driver bundles.
Note: if your LAN card was factory installed (ordered on product option 0D1), you do not need to perform the
following hardware and software installation steps though you still need to configure the card’s IP address as
well as set other parameters and options such as those mentioned in Table 2 The Network Configuration
Worksheet.
These AB465A combination cards can be added to your system or replaced without the need to shut down or
reboot the system--a process called online addition and replacement (OLAR). The following instructions
assume you are not performing online addition and replacement.
Step 1: Access the system card bay
•
If the system is running, first, issue the synccommand. Then shut down the system by executing:
shutdown -h. Respond “y” to the continue to shutdown prompt.
•
Wait for the system to shut down completely, and then power off the system by pressing the system off
button. Ensure that the system is grounded.
•
•
Open the system to gain access to the PCI backplane.
Select an empty PCI or PCI-X slot and remove the slot cover. The card can operate in PCI as well as PCI-X
mode. Some servers have “shared” slots. If you put this card in a shared slot that is shared with a slower
card, both cards will then operate at the slower card’s speed.
Step 2: Install the card
•
Check the latest support matrix to see the systems that support this card, how many cards per system,
under “Networking and Communications.”
•
•
Observe the antistatic precautions. HP recommends wearing ESD straps when installing the card.
Record the serial number and MAC address located on the card for future reference. The MAC address
labelled on the card refers to LAN port A. Add 1 to obtain the MAC address for LAN port B. For fibre
channel, also record the card’s Port and Node worldwide names (WWN). The WWN labelled on each card
refers to WWN for FC port 1 (the left port). Add 2 to obtain the WWN for FC port 2 (the right port).
•
•
Grasp the card by its edges or faceplate with both hands, insert the card into the slot, and firmly but
gently press the card in until it is fully seated.
Secure the card and reassemble the system.
Step 3: Connect the card to the network
•
Attach the connector from a LAN cable to the card (Figure 1 on page 11). Do the same for the second port.
For 1000Base-T, cabling must be Cat 5 UTP or better with RJ-45 connectors. For operating distances,
refer to the “Cable Specifications” section of this document. Note: LAN A is the bottom RJ-45 connector.
3
Hardware and Software Installation Procedure
Step 4: Connect the fibre channel devices
•
Attach the free end of the LAN cable to any unused port on the switch. The Base-T connections on the
card operate at 10 or 100 Mbit/s in either full- or half-duplex modes and at 1000 Mbit/s only in full-duplex
mode. Set the ports on the card and on your switch according to the following table.
Table 1
HP-UX 1000Base-T Supported Configurations
HP-UX 1000Base-T Port
Link Partner
AUTO
Resulting Speed
AUTO
AUTO
10 HD
Highest Common Speed (HP-UX supports 10/100/1000)
1000 FD fixed/manual
1000 Mbit/s FD
10 Mbit/s HD
10 HD (for example, a
10Base-T Hub)
10 FD
100 HD
100 FD
10 FD
100 HD
100 FD
10 Mbit/s FD
100 Mbit/s HD
100 Mbit/s FD
If you are using Jumbo Ethernet frames, ensure that:
1
— all end stations on a given LAN have the same maximum transmission unit (MTU) setting.
— intermediate stations such as switch ports in your LAN have an MTU equal to or greater than the end
station’s MTU.
Step 4: Connect the fibre channel devices
•
Attach the LC connector from a fibre channel cable to the fibre channel connector on the card (Figure 1).
For fibre channel, the cable must be 50 micron MMF. If the remote connection is type SC, you will need
an LC-to-SC cable. Do the same for the other connector.
•
Plug the other end of the fibre channel cable into the connector on your fibre channel switch or device.
Step 5: Prepare to install the software
•
•
•
Ensure power cable is connected to system. Power up the system.
Log in as root.
Check that the /usr/bin, /usr/sbin, and /sbindirectories are in your PATH using the command: echo
$PATH
•
Check the HP-UX version by entering: uname -r
# uname -r
B.11.11
or
B.11.23
The version must be B.11.11 for 11i v 1.0 or B.11.23 for 11i v 2.0.
1. In the Jumbo Frames discussion, “LAN” means that the end stations do not have any routers or
layer 3 switches in between them.
4
Hardware and Software Installation Procedure
Step 6: Install the latest software.
•
Check the Release Notes for GigEther-01 and FibrChanl-01 to see if you need to install any appropriate
and Communications.
Step 6: Install the latest software.
•
Load the software media into the appropriate drive. If you are adding the Gigabit Ethernet software
bundle (GigEther-01) for HP-UX 11i v 1.0, you can get the Gigabit Ethernet driver on the December
2004 (or later) OE distribution media. If loading this product for 11i v 2.0 for the first time, you must load
the entire September 2004 (or later) OE distribution media and you’ll get the needed drivers. Once you’ve
got the required full HP-UX OE installed, you will be able to select and load just the driver bundle if you
want.
•
•
•
Run the swinstallprogram to install the software using the command: swinstall.
Change the host name after “Source Host Name,” if necessary.
Click the Source Depot Path to identify the registered depot for the appropriate source depot path and
activate the OK button to return to the Software Selection Window.
•
•
•
Highlight the 1000Base-T software GigEther-01 (for cards such as AB465A).
Choose Mark for Install from the “Actions” menu to choose the product to be installed.
Choose Install from the “Actions” menu to begin product installation and open the Install Analysis
Window.
•
•
Activate the OK button in the Install Analysis Window when the Status field displays a “Ready” message.
Activate the YES button at the Confirmation Window to confirm that you want to install the software.
swinstallloads the fileset, runs the control scripts for the filesets, and builds the kernel. This should
take about 3 to 5 minutes. When the status field indicates Ready, click Done. A Note Window then opens.
Click the OK button to reboot the system.
•
If you are adding the fibre channel software bundle (FibrChanl-01) for 11i v 1.0, you can find the fibre
channel software bundle on the December 2004 (or later) OE distribution media.
If you are adding the fibre channel software bundle (FibrChanl-01) for 11i v 2.0, you can find the fibre
channel software bundle on the September 2004 (or later) OE distribution media. Just repeat Step 6 to
load it.
Step 7: Configure the card using SAM
•
•
•
•
•
Log in as rootand verify that the card and its hardware path are displayed by entering: ioscan.
Run the System Administration Manager by entering sam.
Double-click Networking and Communications.
Double-click Network Interface Cards.
Highlight the AB465A combination Fibre Channel/Gigabit Ethernet card and choose Configurefrom the
“Actions” menu.
•
•
Fill in the form according to the instructions using the “Network Configuration Worksheet” in this
document.
Click the OK button to activate the card and then select exitfrom the “File” menu until you exit SAM.
5
Hardware and Software Installation Procedure
Step 8: Verify the fibre channel installation
Step 8: Verify the fibre channel installation
•
To verify that the fc driver appears for each installed card, enter:
ioscan -fk
The ioscan output might look like the following:
Class I H/W Path Driver S/W State
fc 4 1/0/8/1/0/4/0 fcd CLAIMED INTERFACE HP AB465-60001 PCI/PCI-X 2-port 2Gb
FC/2-port 1000B-T Combo Adapter (FC Port 1)
fc 5 1/0/8/1/0/4/1 fcd CLAIMED INTERFACE HP AB465-60001 PCI/PCI-X 2-port 2Gb
H/W Type Description
FC/2-port 1000B-T Combo Adapter (FC Port 2)
The last two digits of the hardware path (third column) reflect the path of each port. Both ports need to
show as CLAIMEDhere.
•
Verify that all devices you attached to the fibre channel card are listed in the ioscan output. For example,
if you have a direct attach fibre channel device attached to the system, the ioscan output might look like:
8/12.8.0.255.0.1.0 sdisk CLAIMED DEVICE DGC C3400WDR5
The example above is the hardware path of LUN0 of a directly attached fibre channel mass storage device
with loop ID of 1. If all attached devices are not listed, or for details on interpreting hardware paths, see
the HP Fibre Channel Mass Storage Adapters Support Guide. HP fibre channel installation is verified if
the ioscan output lists all mass storage devices attached to the card.
If the correct driver is installed, but the card does not show in the ioscan output, the driver is not
recognizing the card. Make sure the card is seated and connectors are attached tightly, then if the
problem persists, contact HP for assistance.
Step 9: Verify the LAN installation
•
Verify that the LAN connector’s Link LED is steadily on (this means the card and driver are installed
successfully).
•
Obtain the PPA number and the station address of each card by using the lanscancommand. The MAC
address labelled on each card refers to LAN port A (the right port). Add 1 to obtain the MAC address for
LAN port B.
•
•
To verify link-level connectivity with a remote system, enter:
$ linkloop -i PPA_number remote_station_address
Note: when you use linkloop, ensure that the remote system is on the same subnet and is an
HP-UX-based system.
To verify IP-level connectivity with a remote system, enter:
$ping Remote_IP_Address
and
netstat -in
When you use netstat -in, the output values Ipktsand Opktsshould be incrementing.
6
Hardware and Software Installation Procedure
Optional Step: Configure Jumbo Frames Size (Jumbo frames are supported only at 1000 Mbit/s)
•
•
Installation is complete when you have successfully run linkloop, pingand netstat. To configure
remote systems, see the Ethernet Support Guide available on the web at http://docs.hp.com. Do this step
only if remote systems have not been previously configured.
Optionally, if you want to verify that the igelan driver appears for each installed card, enter: ioscan
-fknClan
The ioscan output for each port would look something like the following:
Class I H/W Path Driver S/W
State H/W Type Description
lan 6 1/0/2/1/0/6/0 igelan CLAIMED INTERFACE HP AB465-60001 PCI/PCI-X 2-port 2Gb
FC/2-port 1000B-T Combo Adapter
The last two digits of the hardware path (third column) reflect the path of each port -- in the sample
CLAIMEDhere.
Optional Step: Configure Jumbo Frames Size (Jumbo frames are supported only at 1000 Mbit/s)
•
Jumbo frames for the igelandriver on HP-UX 11i v 1.0 have an mtu_size of 9000 bytes. On HP-UX 11i v 2.0
of September 2004, jumbo frames using the igelandriver can have an MTU in the range of 1501 to 9000
bytes.
If you are using Jumbo Ethernet frames, ensure that:
1
— all end stations on a given LAN have the same maximum transmission unit (MTU) setting;
— intermediate stations such as switch ports in your LAN have an MTU equal to or greater than the end
station’s MTU.
•
•
Obtain the PPA number of the card by entering lanscan.
Choose one of two configuration methods that will permanently save your configuration.
— use the GUI-based system admin manager (SAM).
To use SAM, type samat the HP-UX system prompt; then double-click Networking and
Communications, and then Advanced Configuration--see Ethernet Support Guide for details, and then
do the steps for verifying the MTU size;
or
edit the following configuration file using an editor such as “vi”:
/etc/rc.config.d/hpigelanconf.
Set the mtusize by editing:
HP_IGELAN_MTU[i]=mtusize, and insert the proper interface name:
HP_IGELAN_MTU[i]=HP_IGELAN_INTERFACE_NAME. When the system reboots, the interface
will be configured for jumbo frame operation.
•
•
Verify MTU change by entering netstat -rn. If MTU has not changed, enter the following commands:
$ifconfig lan PPA_number unplumb
$ifconfig lan PPA_number ip_address netmasknetmask up
To check (or verify) the current Ethernet frame size, enter:
$lanadmin -m PPA_number
1. In the Jumbo Frames discussion, “LAN” means that the end stations do not have any routers or
layer 3 switches in between them.
7
Hardware and Software Installation Procedure
For Further Information
An alternative way to temporarily configure jumbo frame size is to enter:
lanadmin -M mtu_size PPA_number.
Using lanadminis temporary because it will not preserve your settings across reboots.
The PPA_numberis the one we obtained from the output of lanscan. For using Jumbo Frames with the igelan
Gigabit Ethernet driver on HP-UX 11i v 1.0, set the mtu_size to 9000 (bytes). For using Jumbo Frames with
the igelandriver on 11i v 2.0 of September 2004 (or later), set the mtu_size to a number in the range of 1501
to 9000 bytes.
For Further Information
For further information on the Gigabit Ethernet and Fibre Channel as implemented in this card, please refer
primarily located under the subsection called “Combination Cards.”
The AB465A is a 2-port FC and 2-port GigE version of HP’s A9784A combination card; and they both use the
same drivers and firmware -- the drivers are fcdfor Fibre Channel and igelanfor Gigabit Ethernet. To check
for updated information, either look at the information for the A9784A or check the Fibre Channel Support
Matrix and the Ethernet Support Matrix on http://docs.hp.com
Maintenance and troubleshooting information about the igelan Gigabit Ethernet driver used in this
product is located in the Ethernet Support Guide. There is maintenance and troubleshooting information
about the fcd Fibre Channel driver used in this product in the HP Fibre Channel Mass Storage Adapters
Support Guide. There is also a Support Matrix for Gigabit Ethernet and a separate one for Fibre Channel. The
fcd driver is the same one used in the A6826A Fibre Channel product and has the same features as the driver
described in that product’s documentation.
8
Hardware and Software Installation Procedure
Network Configuration Worksheet
Network Configuration Worksheet
Fill out one worksheet for the networking data of each LAN port on the combination card you are installing.
Table 2
Network Configuration Worksheet
Required/
Default
How to Configure
(see Note 1)
Your
System
Data Type
Example
196.6.20.2
Optional
Internet
Address
Required
0.0.0.0
SAM or ifconfigor
edit
/etc/rc.config.d/
netconf
Subnet mask
Required if
using
Subnet mask not used SAM or ifconfigor
255.255.248.0
edit
subnetting
/etc/rc.config.d/
netconf
Station
address
Built-in but can
be optionally
changed
As shown on card
SAM or edit
0x0060b0c4012f
/etc/rc.config.d/
hpigelanconf or
temporarily:
lanadmin -A
Host name
alias for this
network
Required if the
system is
connected to
None
SAM or edit
/etc/hosts
host1
interface (card) more than 1
network
Link
configuration
Required
Required
Optional
Autonegotiating
Autonegotiating
1500 bytes
SAM or temporarily: lanadmin -X
lanadmin -X
auto_on ppa#
(if already
turned off)
Link
speed/duplex
mode
Hub or switch (see
Note 2) SAM or
temporarily:
lanadmin -X
100fd ppa#
lanadmin -X
MTU
SAM or edit
lanadmin -M
(Maximum
Transmission
Unit): Jumbo
Frames
/etc/rc.config.d/ 9000 ppa#(see
hpigelanconfor
temporarily:
Note 3 below)
lanadmin -M
Receive flow
control
Optional
On
SAM or edit
/etc/rc.config.d/ fctrl off
lanadmin -X
hpigelanconfor
temporarily:
lanadmin -X
Note 1: To configure values permanently, edit the configuration files using SAM or an editor such as “vi”.
Using lanadmin will not preserve your settings across reboots.
Note 2: The speed configuration of the card can be 10, 100, or 1000 Mbit/s and is determined by the speed
setting of the hub or switch port to which the card is connected. The card automatically senses this speed. The
Base-T card only runs at one speed at a time. To verify the speed selection, run lanadmin -x ppa#.
9
Hardware and Software Installation Procedure
Cable Specifications
Note 3: The valid MTU size for normal frames using the igelan driver on HP-UX 11i v 1.0 or v 2.0 is 1500
bytes. For Jumbo Frames, the valid MTU size on HP-UX 11i v 1.0 is 9000 , and for HP-UX 11i v 2.0, it is a
number in the range of 1501 to 9000 bytes.
Cable Specifications
Operating Distance for 1000Base-T (Copper UTP): Up to 100 meters — Cat 5 and Cat 5E
Operating distances for fibre channel using multi-mode fiber optic cable are as follows:
Description (Fibre Channel)
Rate
Operating Distance
50/125 micron MMF
50 micron MMF
2 Gbits/s
1 Gbits/s
300 meters (984 ft)
500 meters (1640 ft)
Available HP Fiber Optic Cables:
LC-LC
C7524A
Fibre Channel Cable 2m LC duplex 50/125 M/M Optical
Fibre Channel Cable 16m LC duplex 50/125 M/M Optical
Fibre Channel Cable 50m LC duplex 50/125 M/M Optical
C7525A
C7526A
LC-SC
C7529A
Fibre Channel Cable 2m LC-SC duplex 50/125 M/M Optical
Fibre Channel Cable 16m LC-SC duplex 50/125 M/M Optical
C7530A
Adapter/Extenders
C7534A
Fibre Channel Adapter SC Form Factor
Adapter Kit
C7540A
Fibre Optic Adapter Kit - Optical: Includes 2m LC/SC Cable and F/F
extender
10
Hardware and Software Installation Procedure
Figure 1
AB465A PCI-X 2-Port 2Gb FC/ 2-Port 1000B-T Combination Card
Port 1
Fibre Channel Connectors
(Duplex LC)
Speed LEDS (Port 2)
1Gb
2Gb
2Gb
1Gb
Speed LEDS (Port 1)
Port 2
Activity/Link LEDs
Flashing = Data traffic
Solid
= Active link
LAN B
LAN A
OFF = No link
1000Base-T Connectors
(RJ-45)
}
Speed LEDs
Off
Green = 100 Mbit/s
Yellow = 1000 Mbit/s
=
10 Mbit/s
11
Hardware and Software Installation Procedure
Features
Features
The AB465A PCI-X Combination cards have the following features:
•
PCI-X 133 MHz capable card. It can operate at 32-bit or 64-bit compatible modes and is supported in the
following frequencies: PCI 66, PCI-X 66, and PCI-X 133. Best performance is achieved by putting the card
in a “dual-rope” PCI-X 133 slot. To identify which slots are the dual rope slots in a particular system,
please refer to the hardware users’ guide for each system. The AB465A card is not supported in PCI 33
bus mode. It operates in 3.3V slots only.
•
Supports HP-UX 11i v 2.0 (64 bit) of September 2004 (or later) or 11i v 1.0 of December 2004 (or
later) on HP 9000 (PA-RISC-based) and HP Integrity (Itanium or Itanium2-based) platforms.
•
•
•
The Gigabit Ethernet ports support use of Jumbo Frames.
Supports HP Serviceguard and Auto-Port Aggregation (APA) for high availability.
The Gigabit Ethernet port supports virtual LANs (VLANs). This feature is described in Using HP-UX
•
Supports PCI-X online addition/replacement (OLA/R) on specified systems.For instructions on how to
perform online addition and replacement (OLAR) for PA-RISC-based systems running HP-UX 11i v 1.0,
see Configuring HP-UX For Peripherals. For instructions on performing OL* for Itanium-based systems
and PA-RISC systems running HP-UX 11i v 2.0 of September 2004 or later, refer to the Interface Card
OL* Support Guide.
•
•
Supports configuration through SAM or command line.
vPars support with vPars 3.02 on supported HP 9000 (PA-RISC-based) systems. Boot over vPars is
supported only on the Fibre Channel ports.
•
•
•
•
•
Supports 16k LUNs on the Fibre Channel ports.
Supports boot/dump on Fibre Channel ports only.
Online/Offline Diagnostics.
Ignite UX support.
Supports readout of Vital Product Data (VPD) for Fibre Channel. To read the Fibre Channel VPD, use:
fcmsutil devicefilename vpd.
•
Firmware for the Fibre Channel ports -- version is 3.3.150 as of the publication of this document. The FC
EFI driver firmware version is 1.42. For GigE, the bootcode is version 3.27; EFI is v7.0.10 or later. To
check for updates of these, see the section “For Further Information” in this document.
•
•
•
•
Fibre channel transfer rates of 2Gbit/s and 1Gbit/s
Auto speed sensing on the Fibre Channel ports.
Supports Fibre Channel protocols SCSI-FCP-2 and FC-Tape.
Supports the following Fibre Channel topologies:
— FC-SW
— FC-AL-2
— FC-FLA
— FC-PLDA
12
Hardware and Software Installation Procedure
Interoperability: Supported Systems
Interoperability: Supported Systems
Supported Systems
The combination card is supported in the HP Integrity (Itanium or Itanium2-based) systems specified in
Table 3.
Table 3
Combination Card in HP Integrity Systems
rx1600, rx1620 ; These servers accommodate 1 AB465A per system.
rx2600
rx2620
rx4640
rx7620
HP Integrity Superdome IA 16-way, 32-way, 64-way, and 128-way
rx8620 and rx8620 with I/O Expansion unit
The combination card is supported in the HP 9000 (PA-RISC processor-based) systems specified in Table 4.
Table 4
Combination Card in HP 9000 Systems
rp3410-2
rp3440-4
rp4440-8
rp7420-16
HP 9000 Superdome (3.3 volt slots) PA 16-way, 32-way, 64-way, and 128-way
rp8420 and rp8420 with I/O Expansion unit
13
Card Physical and Environmental Specs and Regulatory Information
Card Physical and Environmental Specifications
Card Physical and Environmental
Specs and Regulatory Information
Card Physical and Environmental Specifications
Following are the product physical and environmental specifications of the AB465A PCI-X 2-Port 2 Gigabit
Fibre Channel and 2-Port Gigabit Ethernet Combination Card.
Physical Specifications
Form Factor
PCI support
Height
PCI-X (rev 2.3) full-height card
64-bit 3.3V only 133Mhz
10.668 cm (4.2 in)
Depth
16.9 cm (6.6 in)
Width
1.295 cm (0.51 in)
Weight
0.18 kg (0.4 lb) kg
Electrical
Power consumption:
25 Watts
Environmental
Temperature
Degrees F = (1.8 x Degrees C) + 32
o
o
Operating Temperature Range (Degrees Celsius)
+5 C to 40 C
o
o
Recommended Operating Temperature Range
(Degrees Celsius)
+10 C to 30 C
o
o
Non-operating/ storage Temperature Range (Degrees
Celsius)
-40 C to 70 C
Temperature Shock Immunity - Max Rate of Change
Non-operating/storage Humidity Range in %RH
20 C/hr
90
Recommended Operating Humidity Range @ 22
Degrees Celsius in %RH
40 to 60
Heat Dissipation (in Watts)
17
8
Maximum kV (if less than 15 kV) with no loss of
function
Maximum kV (if less than 25 kV) with no component 25
damage
14
Card Physical and Environmental Specs and Regulatory Information
Card Physical and Environmental Specifications
Operating Altitude
3,000 meters (9900) ft
4,500 meters (14850 ft)
Non-operating Altitude
Electromagnetic Compatibility
This document contains regulatory statements for the United States and the European community.
15
Card Physical and Environmental Specs and Regulatory Information
FCC Statement (For U.S.A.)
FCC Statement (For U.S.A.)
Federal Communications Commission Radio Frequency Interference Statement
WARNING
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference and
(2) this device must accept any interference received, including interference that
might cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy, and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at his own expense will be required to take whatever measures
may be required to correct the interference.
Hewlett-Packard’s system certification tests were conducted with HP-supported
peripheral devices and cables, such as those received with your system. Changes or
modifications to this equipment not expressly approved by Hewlett-Packard could
void the user’s authority to operate the equipment.
Canada
Warning: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matériel brouilleur du
Canada.
EMI Statement (European Community)
NOTE
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case you may be required to take adequate measures.
16
Card Physical and Environmental Specs and Regulatory Information
Laser Safety Statements
Laser Safety Statements
Laser Safety Statements - U.S. FDA/CDRH - Optical (laser) Transceiver
CAUTION
The optical transceiver provided on the network interface card contains a laser system and is
classified as a “Class-I Laser Product” under a U.S. Department of Health and Human Services
(DHHS) Radiation Performance standard according to the Radiation Control for Health and
Safety Act of 1968. The Class I label and compliance statement are located on the optical
transceiver.
To ensure proper use of this product, please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an authorized service location.
CAUTION
Use of controls, adjustments or the performance procedures other than those specified herein
may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not
try to open the enclosure.
Laser Safety - European Union - Optical Transceiver Only
CAUTION
The optical transceiver provided on the network interface card contains a laser system and is
classified as a “Class 1 Laser Product” per EN 60825-1, Safety of Laser products. Class 1 laser
products are considered safe and do not pose a biological hazard if used within the data sheet
limits and instructions.
To ensure proper use of this product, please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an authorized service location.
CAUTION
Use of controls, adjustments or the performance procedures other than those specified herein
may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not
try to open the enclosure.
There are no user serviceable parts nor any maintenance required for the optical transceiver. All adjustments
are made at the factory before shipment to customers. Tampering with or any attempt to modify the optical
transceiver will result in voided product warranty. It may also result in improper operation of the network
card circuitry and possible overstress of the laser source. Device degradation or product failure may result.
17
Card Physical and Environmental Specs and Regulatory Information
Laser Safety Statements
18
|