HP Hewlett Packard Network Card 3C509B ISA User Manual

3COM Etherlink III 3C509B ISA  
10BT Network Adapter  
Installation Guide  
 
General information to read before installing  
General information to read before installing  
• On all systems : Before installing LAN card, go into Bios setup and set PnP  
OS field to NO.  
• How to change LAN card configuration if needed (Advanced users only)  
This is a general advisory on how to forcibly modify resources for ISA and PCI network  
cards.  
ISA cards:  
• For ISA network adapters, start the configuration tool provided in driver  
kit (See install documentation)  
• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-  
sion > reserve an IRQ for the adapter.  
PCI cards:  
• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA  
IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.  
ISA cards can’t use IRQ9  
• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s  
inability to share IRQs.  
• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:  
1 Install the NIC then power up the system.  
2 Press F2 to go to CMOS setup.  
3 Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation  
section)  
4 Save the configuration settings and boot to the applicable OS.  
5 Follow installation steps.  
Sound conflict under Win 95 on VLi8 only  
• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-  
vice under Win95.  
• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:  
1 Install the NIC then power up the system  
 
General information to read before installing  
2 Press F2 to go to CMOS setup.  
3 Set PNP OS to NO and reserve IRQ 5.  
4 Save settings and boot to applicable OS.  
 
1 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows 95 SR2.5  
1 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows 95  
SR2.5  
Connecting to a  
Windows NT 3.51 Server  
Requirements  
• HP Vectra with Windows 95 SR2.5.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows 95 SR2.5 media.  
• Microsoft Windows NT 3.51 Server system that supports NetBEUI,  
NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network  
protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
5
03  
07  
I/O Address  
210  
210  
210  
Procedure  
1 Power on the system and start Windows 95SR2.5.  
2 From the 3COM 3C509B driver disk, run PREINSTL.EXE.  
3 Shutdown and power down the system. With the HP Vectra turned off,  
install the 3COM 3C509B network adapter into an ISA slot.  
4 Connect network cable media to the 3COM 3C509B network adapter.  
5 Power on the system and press “SHIFT-<F5>” to boot to Windows 95  
command prompt.  
6 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
7 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
8 If changes are required, save those changes and exit.  
 
1 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 3.51 Server  
9 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
95SR2.5.  
10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B  
network adapter as “3Com 3C509B EtherLink III”.  
11 Insert the 3COM 3C509B driver disk in the floppy drive and click on  
“Next” from the Update Device Driver Wizard dialog box.  
12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA  
(3C509b-TP) in PnP mode”, click on “Finish”.  
13 During the Update Device Driver process, point to the appropriate file  
locations (i.e. drivers disk or Windows 95 CD) to install the necessary  
files. Keep newer files when a file being copied is older than the file  
currently on your computer.  
14 Click on “OK” when the system prompts for the computer and workgroup  
names.  
15 Enter the Computer Name, Workgroup, and Computer Description in the  
appropriate spaces and click on “Close” (Contact your network  
administrator if you do not have the required information).  
NOTE  
According to 3COM, click on “OK” to ignore the error message indicating  
“Error enumerating cards. The NIC specific DLL TCAUM509 did not find any  
NICs present.”  
16 Click on “YES” to restart the system when prompted.  
17 Right-click on the “Network Neighborhood” icon and select “Properties”.  
18 Accept the default Network Protocols and the Primary Network Logon  
(Client for Microsoft Networks) as seen below and click on “OK”. (If you  
do not have the required information, contact your network  
administrator)  
19 Client for Microsoft Networks  
Client for Microsoft Networks  
3Com EtherLink III ISA (3C509b-TPO) in PnP mode  
3Com TCAATDI Diagnostic TDI  
IPX/SPX-compatible Protocol  
NetBEUI  
20 Click on “OK” to accept the configuration.  
21 When prompted, specify the path to your Windows 95 files.  
22 Click on “Yes” when prompted to restart the system.  
 
2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows 95 SR2.5  
2 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows 95  
SR2.5  
Connecting to a  
Windows NT 4.0 Server  
Requirements  
• HP Vectra with Windows 95 SR2.5.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and drivers  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows 95 SR2.5 media.  
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink  
IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.  
• Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
03  
07  
I/O Address  
210  
210  
210  
Procedure  
1 Power on the system and start Windows 95SR2.5.  
2 From the 3COM 3C509B driver disk, run PREINSTL.EXE.  
3 Shutdown and power down the system. With the HP Vectra turned off,  
install the 3COM 3C509B network adapter into an ISA slot.  
4 Connect network cable media to the 3COM 3C509B network adapter.  
5 Power on the system and press “SHIFT-<F5>” to boot to Windows 95  
command prompt.  
6 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
7 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
8 If changes are required, save those changes and exit.  
9 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
95SR2.5.  
 
2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 4.0 Server  
10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B  
network adapter as “3Com 3C509B EtherLink III”.  
11 Insert the 3COM 3C509B driver disk in the floppy drive and click on  
“Next” from the Update Device Driver Wizard dialog box.  
12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA  
(3C509b-TP) in PnP mode”, click on “Finish”.  
13 During the Update Device Driver process, point to the appropriate file  
locations (i.e. drivers disk or Windows 95 CD) to install the necessary  
files. Keep newer files when a file being copied is older than the file  
currently on your computer.  
14 Click on “OK” when the system prompts for the computer and workgroup  
names.  
15 Enter the Computer Name, Workgroup, and Computer Description in the  
appropriate spaces and click on “Close” (Contact your network  
administrator if you do not have the required information).  
16 Note: According to 3COM, click on “OK” to ignore the error message  
indicating “Error enumerating cards. The NIC specific DLL TCAUM509  
did not find any NICs present.”  
17 Click on “YES” to restart the system when prompted.  
18 Right-click on the “Network Neighborhood” icon and select “Properties”.  
19 Accept the default Network Protocols and the Primary Network Logon  
(Client for Microsoft Networks) as seen below and click on “OK”. (If you  
do not have the required information, contact your network  
administrator)  
20 Client for Microsoft Networks  
Client for Microsoft Networks  
3Com EtherLink III ISA (3C509b-TPO) in PnP mode  
3Com TCAATDI Diagnostic TDI  
IPX/SPX-compatible Protocol  
NetBEUI  
21 Click on “OK” to accept the configuration.  
22 When prompted, specify the path to your Windows 95 files.  
23 Click on “Yes” when prompted to restart the system.  
 
3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows 95 SR2.5  
3 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows 95  
SR2.5  
Connecting to a NetWare Requirements  
3.12 Server  
• HP Vectra with Windows 95 SR2.5.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and drivers  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows 95 SR2.5 media.  
• Novell NetWare 3.12 Server that supports IPX network protocol.  
• Novell Client for Windows 95 v2.5 installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
5
03  
07  
I/O Address  
210  
210  
210  
Procedure  
1 Power on the system and start Windows 95SR2.5.  
2 From the 3COM 3C509B driver disk, run PREINSTL.EXE.  
3 Shutdown and power down the system. With the HP Vectra turned off,  
install the 3COM 3C509B network adapter into an ISA slot.  
4 Connect network cable media to the 3COM 3C509B network adapter.  
5 Power on the system and press “SHIFT-<F5>” to boot to Windows 95  
command prompt.  
6 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
7 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
8 If changes are required, save those changes and exit.  
 
3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a NetWare 3.12 Server  
9 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
95SR2.5.  
10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B  
network adapter as “3Com 3C509B EtherLink III”.  
11 Insert the 3COM 3C509B driver disk in the floppy drive and click on  
“Next” from the Update Device Driver Wizard dialog box.  
12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA  
(3C509b-TP) in PnP mode”, click on “Finish”.  
13 During the Update Device Driver process, point to the appropriate file  
locations (i.e. drivers disk or Windows 95 CD) to install the necessary  
files. Keep newer files when a file being copied is older than the file  
currently on your computer.  
14 Click on “OK” when the system prompts for the computer and workgroup  
names.  
15 Enter the Computer Name, Workgroup, and Computer Description in the  
appropriate spaces and click on “Close” (Contact your network  
administrator if you do not have the required information).  
NOTE  
According to 3COM, click on “OK” to ignore the error message indicating  
“Error enumerating cards. The NIC specific DLL TCAUM509 did not find any  
NICs present.”  
16 Click on “YES” to restart the system when prompted.  
17 From the location of the “Novell Client for Windows 95 v.2.5” installation  
files, execute “Setup.exe”.  
18 Click on “Yes” to accept the License Agreement.  
19 Select “Custom” installation and click on “Next”.  
20 Select “Bindery (NetWare 3.x)” and click on “Next”.  
21 Click on “Install” to start the installation.  
22 Click on “Yes” to set the Preferred Server. (If you do not have the  
required information, contact your network administrator).  
23 Click on “Reboot” to complete the installation.  
24 Right-click on the “Network Neighborhood” icon and select “Properties”.  
25 Accept the default Network Protocols and the Primary Network Logon to  
(Novell NetWare Client) as seen below and click on “OK”. (If you do not  
have the required information, contact your network administrator)  
 
3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a NetWare 3.12 Server  
26 Novell NetWare Client  
Novell NetWare Client  
3COM Etherlink III Bus-Master PCI Ethernet Adapter  
IPX 32-bit Protocol for the Novell NetWare Client  
IPX/SPX-compatible Protocol  
NetBEUI  
27 When prompted, specify the path to your Windows 95 files.  
28 Click on “Yes” when prompted to restart the system.  
 
4 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows 95 SR2.5  
4 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows 95  
SR2.5  
Connecting to a NetWare Requirements  
4.11 Server  
• HP Vectra with Windows 95 SR2.5.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and drivers  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows 95 SR2.5 media.  
• Novell NetWare 4.11 Server that supports IPX network protocol.  
• Novell Client for Windows 95 v2.5 installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
03  
07  
I/O Address  
210  
210  
210  
Procedure  
1 Power on the system and start Windows 95SR2.5.  
2 From the 3COM 3C509B driver disk, run PREINSTL.EXE.  
3 Shutdown and power down the system. With the HP Vectra turned off,  
install the 3COM 3C509B network adapter into an ISA slot.  
4 Connect network cable media to the 3COM 3C509B network adapter.  
5 Power on the system and press SHIFT-<F5> to boot to Windows 95  
command prompt.  
6 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
7 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
8 If changes are required, save those changes and exit.  
 
4 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a NetWare 4.11 Server  
9 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
95SR2.5.  
10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B  
network adapter as “3Com 3C509B EtherLink III”.  
11 Insert the 3COM 3C509B driver disk in the floppy drive and click on  
“Next” from the Update Device Driver Wizard dialog box.  
12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA  
(3C509b-TP) in PnP mode”, click on “Finish”.  
13 During the Update Device Driver process, point to the appropriate file  
locations (i.e. drivers disk or Windows 95 CD) to install the necessary  
files. Keep newer files when a file being copied is older than the file  
currently on your computer.  
14 Click on “OK” when the system prompts for the computer and workgroup  
names.  
15 Enter the Computer Name, Workgroup, and Computer Description in the  
appropriate spaces and click on “Close” (Contact your network  
administrator if you do not have the required information).  
NOTE  
According to 3COM, click on “OK” to ignore the error message indicating  
“Error enumerating cards. The NIC specific DLL TCAUM509 did not find any  
NICs present.”  
16 Click on “YES” to restart the system when prompted.  
17 From the location of the “Novell Client for Windows 95 v.2.5” installation  
files, execute “Setup.exe”.  
18 Click on “Yes” to accept the License Agreement.  
19 Select “Custom” installation and click on “Next”.  
20 Select “NDS (NetWare 4.x or higher) and click on “Next”.  
21 Click on “Install” to start the installation.  
22 Click on “Yes” to set the Preferred Tree, Server, etc. (If you do not have  
the required information, contact your network administrator).  
23 Click on “Reboot” to complete the installation.  
24 Right-click on the “Network Neighborhood” icon and select “Properties”.  
25 Accept the default Network Protocols and the Primary Network Logon to  
(Novell NetWare Client) as seen below and click on “OK”. (If you do not  
have the required information, contact your network administrator).  
 
4 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a NetWare 4.11 Server  
26 Novell NetWare Client  
Novell NetWare Client  
3COM Etherlink III Bus-Master PCI Ethernet Adapter  
IPX 32-bit Protocol for the Novell NetWare Client  
IPX/SPX-compatible Protocol  
NetBEUI  
27 When prompted, specify the path to your Windows 95 files.  
28 Click on “Yes” when prompted to restart the system.  
 
5 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 4.0 Workstation  
5 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
4.0 Workstation  
Connecting to a  
Windows NT 3.51 Server  
Requirements  
• HP Vectra with Windows NT 4.0 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND4.SYS, version 5.26.40  
• Microsoft Windows NT 4.0 Workstation media.  
• Microsoft Windows NT 4.0 Service Pack 4 media.  
• Microsoft Windows NT 3.51 Server system that supports NetBEUI,  
NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network  
protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
5
5
5
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
5 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 3.51 Server  
8 Log onto Windows NT4 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Right-click on the “Network Neighborhood” icon and select “Properties”.  
10 Click on “Yes” when prompted to install Windows NT Networking.  
11 Select “Wired to the network” and click on “Next”.  
12 Click on the “Select from list…” button and then the “Have Disk…”  
button.  
13 Insert the 3COM 3C509B driver disk in the floppy drive.  
14 Set the path to “A:\” in the dialog-box and click on “OK”.  
15 Choose by highlighting the “3Com EtherLink (3c509) ISA Adapter” and  
click on “OK”.  
16 With “3Com EtherLink (3c509) ISA Adapter”listed in the “Network  
Adapters” window, click on “Next”.  
17 Select the applicable network protocols and click on ”Next” (Contact your  
network administrator if you do not have the required information).  
18 At the “Network Services:” prompt, accept default settings and click on  
“Next”.  
19 Click on “Next” to continue the network card installation.  
20 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT4 Workstation CD) in the dialog box and click on “Continue”.  
21 Select ISA for the BUS Type and click on “OK”.  
22 The 3COM Installation Wizard will start. This wizard configures the  
network adapter.  
Select Custom Installation and click on “Next”.  
Set adapter resources according to values noted above and click on  
“Next”.  
Perform NIC Test and click on “Next” if the adapter is operating correctly.  
Perform Network Connection Test and click on “Next” if connectivity is  
verified.  
Do not configure Dynamic Access feature and click on “Next”.  
Do not save setting for a future NIC installation and click on “Next”.  
Click on “Finish” to complete the installation.  
23 Set the path to “A:\” in the dialog box and click on “Continue”.  
24 At the “Show Bindings for:” prompt, accept the default settings and click  
on “Next”.  
25 Click on “Next” to start the network.  
 
5 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 3.51 Server  
26 Specify your Computer Name, Workgroup or Domain (Contact your  
network administrator if you do not have the required information) and  
click on “Next”.  
27 Click on “Finish” to complete the installation.  
28 Remove the 3Com driver disk from the floppy drive and select “Yes” at the  
prompt to shut down and restart your computer for the new settings to  
take effect.  
29 Log onto Windows NT4 Workstation with administrator privileges.  
30 Install the Windows NT4 Service Pack 4 application to correct the error  
messages in the Event Viewer.  
31 Install the Hewlett-Packard Soft-Power Down application once the  
Service Pack 4 has been installed.  
 
6 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 4.0 Workstation  
6 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
4.0 Workstation  
Connecting to a  
Windows NT 4.0 Server  
Requirements  
• HP Vectra with Windows NT 4.0 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND4.SYS, version 5.26.40  
• Microsoft Windows NT 4.0 Workstation media.  
• Microsoft Windows NT 4.0 Service Pack 4 media.  
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink  
IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
6 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 4.0 Server  
8 Log onto Windows NT4 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Right-click on the “Network Neighborhood” icon and select “Properties”.  
10 Click on “Yes” when prompted to install Windows NT Networking.  
11 Select “Wired to the network” and click on “Next”.  
12 Click on the “Select from list…” button and then the “Have Disk…”  
button.  
13 Insert the 3COM 3C509B driver disk in the floppy drive.  
14 Set the path to “A:\” in the dialog-box and click on “OK”.  
15 Choose by highlighting the “3Com EtherLink (3c509) ISA Adapter” and  
click on “OK”.  
16 With “3Com EtherLink (3c509) ISA Adapter”listed in the “Network  
Adapters” window, click on “Next”.  
17 Select the applicable network protocols and click on ”Next” (Contact your  
network administrator if you do not have the required information).  
18 At the “Network Services:” prompt, accept default settings and click on  
“Next”.  
19 Click on “Next” to continue the network card installation.  
20 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT4 Workstation CD) in the dialog box and click on “Continue”.  
21 Select ISA for the BUS Type and click on “OK”.  
22 The 3COM Installation Wizard will start. This wizard configures the  
network adapter.  
Select Custom Installation and click on “Next”.  
Set adapter resources according to values noted above and click on  
“Next”.  
Perform NIC Test and click on “Next” if the adapter is operating correctly.  
Perform Network Connection Test and click on “Next” if connectivity is  
verified.  
Do not configure Dynamic Access feature and click on “Next”.  
Do not save setting for a future NIC installation and click on “Next”.  
Click on “Finish” to complete the installation.  
23 Set the path to “A:\” in the dialog box and click on “Continue”.  
24 At the “Show Bindings for:” prompt, accept the default settings and click  
on “Next”.  
25 Click on “Next” to start the network.  
 
6 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 4.0 Server  
26 Specify your Computer Name, Workgroup or Domain (Contact your  
network administrator if you do not have the required information) and  
click on “Next”.  
27 Click on “Finish” to complete the installation.  
28 Remove the 3Com driver disk from the floppy drive and select “Yes” at the  
prompt to shut down and restart your computer for the new settings to  
take effect.  
29 Log onto Windows NT4 Workstation with administrator privileges.  
30 Install the Windows NT4 Service Pack 4 application to correct the error  
messages in the Event Viewer.  
31 Install the Hewlett-Packard Soft-Power Down application once the  
Service Pack 4 has been installed.  
 
7 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 4.0 Workstation  
7 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
4.0 Workstation  
Connecting to a Novell Requirements  
NetWare 3.12 Server  
• HP Vectra with Windows NT 4.0 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND4.SYS, version 5.26.40  
• Microsoft Windows NT 4.0 Workstation media.  
• Microsoft Windows NT 4.0 Service Pack 4 media.  
• Novell NetWare 3.12 Server that supports IPX network protocol.  
• Novell IntranetWare Client for Windows NT v4.11b installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
7 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 3.12 Server  
8 Log onto Windows NT4 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Right-click on the “Network Neighborhood” icon and select “Properties”.  
10 Click on “Yes” when prompted to install Windows NT Networking.  
11 Select “Wired to the network” and click on “Next”.  
12 Click on the “Select from list…” button and then the “Have Disk…”  
button.  
13 Insert the 3COM 3C509B driver disk in the floppy drive.  
14 Set the path to “A:\” in the dialog-box and click on “OK”.  
15 Choose by highlighting the “3Com EtherLink (3c509) ISA Adapter” and  
click on “OK”.  
16 With “3Com EtherLink (3c509) ISA Adapter”listed in the “Network  
Adapters” window, click on “Next”.  
17 Select the applicable network protocols and click on ”Next” (Contact your  
network administrator if you do not have the required information).  
18 At the “Network Services:” prompt, accept default settings and click on  
“Next”.  
19 Click on “Next” to continue the network card installation.  
20 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT4 Workstation CD) in the dialog box and click on “Continue”.  
21 Select ISA for the BUS Type and click on “OK”.  
22 The 3COM Installation Wizard will start. This wizard configures the  
network adapter.  
Select Custom Installation and click on “Next”.  
Set adapter resources according to values noted above and click on  
“Next”.  
Perform NIC Test and click on “Next” if the adapter is operating correctly.  
Perform Network Connection Test and click on “Next” if connectivity is  
verified.  
Do not configure Dynamic Access feature and click on “Next”.  
Do not save setting for a future NIC installation and click on “Next”.  
Click on “Finish” to complete the installation.  
23 Set the path to “A:\” in the dialog box and click on “Continue”.  
24 At the “Show Bindings for:” prompt, accept the default settings and click  
on “Next”.  
25 Click on “Next” to start the network.  
 
7 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 3.12 Server  
26 Specify your Computer Name, Workgroup or Domain (Contact your  
network administrator if you do not have the required information) and  
click on “Next”.  
27 Click on “Finish” to complete the installation.  
28 Remove the 3Com driver disk from the floppy drive and select “Yes” at the  
prompt to shut down and restart your computer for the new settings to  
take effect.  
29 Log onto Windows NT4 Workstation with administrator privileges.  
30 From the location of the “Novell IntranetWare Client v.4.11b” installation  
files, execute “Setupnw.exe”.  
31 Click on “Continue” to continue with the Novell IntranetWare Client  
installation.  
32 Click on “Yes” to agree to the Software License Agreement to begin  
installation.  
33 Click on the “Reboot” button at the completion of the Novell NetWare  
Client installation to restart the machine for changes to take effect.  
34 Click on the “IntranetWare” tab of the Novell IntranetWare Client Services  
Login screen.  
35 Select “Bindery Login” and specify the Server Name (Contact your  
network administrator if you do not have the required information).  
36 Click on the “Login” tab and specify your Name and Password to login.  
37 Install the Windows NT4 Service Pack 4 application to correct the error  
messages in the Event Viewer.  
38 Install the Hewlett-Packard Soft Power Down application once the  
Service Pack 4 has been installed.  
 
8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 4.0 Workstation  
8 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
4.0 Workstation  
Connecting to a Novell Requirements  
NetWare 4.11 Server  
• HP Vectra with Windows NT 4.0 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND4.SYS, version 5.26.40  
• Microsoft Windows NT 4.0 Workstation media.  
• Microsoft Windows NT 4.0 Service Pack 4 media.  
• Novell NetWare 4.11 server that supports IPX network protocol.  
• Novell IntranetWare Client for Windows NT v4.11b installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 4.11 Server  
8 Log onto Windows NT4 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Right-click on the “Network Neighborhood” icon and select “Properties”.  
10 Click on “Yes” when prompted to install Windows NT Networking.  
11 Select “Wired to the network” and click on “Next”.  
12 Click on the “Select from list…” button and then the “Have Disk…”  
button.  
13 Insert the 3COM 3C509B driver disk in the floppy drive.  
14 Set the path to “A:\” in the dialog-box and click on “OK”.  
15 Choose by highlighting the “3Com EtherLink (3c509) ISA Adapter” and  
click on “OK”.  
16 With “3Com EtherLink (3c509) ISA Adapter”listed in the “Network  
Adapters” window, click on “Next”.  
17 Select the applicable network protocols and click on ”Next” (Contact your  
network administrator if you do not have the required information).  
18 At the “Network Services:” prompt, accept default settings and click on  
“Next”.  
19 Click on “Next” to continue the network card installation.  
20 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT4 Workstation CD) in the dialog box and click on “Continue”.  
21 Select ISA for the BUS Type and click on “OK”.  
22 The 3COM Installation Wizard will start. This wizard configures the  
network adapter.  
Select Custom Installation and click on “Next”.  
Set adapter resources according to values noted above and click on  
“Next”.  
Perform NIC Test and click on “Next” if the adapter is operating correctly.  
Perform Network Connection Test and click on “Next” if connectivity is  
verified.  
Do not configure Dynamic Access feature and click on “Next”.  
Do not save setting for a future NIC installation and click on “Next”.  
Click on “Finish” to complete the installation.  
23 Set the path to “A:\” in the dialog box and click on “Continue”.  
24 At the “Show Bindings for:” prompt, accept the default settings and click  
on “Next”.  
25 Click on “Next” to start the network.  
 
8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 4.11 Server  
26 Specify your Computer Name, Workgroup or Domain (Contact your  
network administrator if you do not have the required information) and  
click on “Next”.  
27 Click on “Finish” to complete the installation.  
28 Remove the 3Com driver disk from the floppy drive and select “Yes” at the  
prompt to shut down and restart your computer for the new settings to  
take effect.  
29 Log onto Windows NT4 Workstation with administrator privileges.  
30 From the location of the “Novell IntranetWare Client v.4.11b” installation  
files, execute “Setupnw.exe”.  
31 Click on “Continue” to continue with the Novell IntranetWare Client  
installation.  
32 Click on “Yes” to agree to the Software License Agreement to begin  
installation.  
33 Click on the “Reboot” button at the completion of the Novell NetWare  
Client installation to restart the machine for changes to take effect.  
34 Click on the “IntranetWare” tab of the Novell IntranetWare Client Services  
Login screen.  
35 Select “NDS Login” and specify the Preferred Server Name (Contact your  
network administrator if you do not have the required information).  
36 Click on the “Login” tab and specify your Name and Password to login.  
37 Install the Windows NT4 Service Pack 4 application to correct the error  
messages in the Event Viewer.  
38 Install the Hewlett-Packard Soft Power Down application once the  
Service Pack 4 has been installed.  
 
9 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 3.51 Workstation  
9 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
3.51 Workstation  
Connecting to a  
Windows NT 3.51 Server  
Requirements  
• HP Vectra with Windows NT 3.51 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows NT 3.51 Workstation media.  
• Microsoft Windows NT 3.51 Service Pack 5.  
• Microsoft Windows NT 3.51 Server system that supports NetBEUI,  
NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network  
protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
10  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
9 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 3.51 Server  
8 Log onto Windows NT3.51 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Open the “Network” icon in the “Control Panel” program group.  
10 Click on “YES” in the “Network Settings” dialog box to install Windows NT  
Networking.  
11 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive.  
12 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window  
and click on “Continue”.  
13 Click on the “Do Not Detect” button from the “Network Adapter Card  
Detection” window, and click on the “Continue” button in the following  
“Network Adapter Card Detection” window.  
14 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer”, then click on “Continue”.  
15 Set the path to “A:\” in the “Insert Disk” dialog box, and then insert the  
3COM driver disk in the floppy drive and click “OK”.  
16 Select “3COM Etherlink (3c509) ISA Adapter” in the “Select OEM  
Option” dialog box, and click “OK”.  
17 Select ISA for the BUS Type and click on “OK”.  
18 Choose the appropriate network protocols by clicking the check boxes in  
the “Windows NT Setup” dialog box and click on the “Continue” button  
(Contact your network administrator if you do not have the required  
information).  
19 Press “OK” to continue from “Network Settings” dialog box.  
20 If applicable, press “OK” to continue from “NWLink IPX/SPX Protocol  
Configuration” dialog box.  
21 At the “Domain/Workgroup Settings” dialog box, click on “OK” to accept  
the default “Workgroup” as your workgroup name.  
22 To complete the installation, remove the floppy disk, and click on “Restart  
computer” in the “Windows NT Workstation Networking Setup” dialog  
box.  
23 Install the Windows NT3.51 Service Pack 5 application.  
 
10 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 3.51 Workstation  
10 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
3.51 Workstation  
Connecting to a  
Windows NT 4.0 Server  
Requirements  
• HP Vectra with Windows NT3.51 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows NT 3.51 Workstation media.  
• Microsoft Windows NT 3.51 Service Pack 5.  
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink  
IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
10  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
10 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 4.0 Server  
8 Log onto Windows NT3.51 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Open the “Network” icon in the “Control Panel” program group.  
10 Click on “YES” in the “Network Settings” dialog box to install Windows NT  
Networking.  
11 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive.  
12 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window  
and click on “Continue”.  
13 Click on the “Do Not Detect” button from the “Network Adapter Card  
Detection” window, and click on the “Continue” button in the following  
“Network Adapter Card Detection” window.  
14 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer”, then click on “Continue”.  
15 Set the path to “A:\” in the “Insert Disk” dialog box, and then insert the  
3COM driver disk in the floppy drive and click “OK”.  
16 Select “3COM Etherlink (3c509) ISA Adapter” in the “Select OEM  
Option” dialog box, and click “OK”.  
17 Select ISA for the BUS Type and click on “OK”.  
18 Choose the appropriate network protocols by clicking the check boxes in  
the “Windows NT Setup” dialog box and click on the “Continue” button  
(Contact your network administrator if you do not have the required  
information).  
19 Press “OK” to continue form “Network Settings” dialog box.  
20 If applicable, press “OK” to continue form “NWLink IPX/SPX Protocol  
Configuration” dialog box.  
21 At the “Domain/Workgroup Settings” dialog box, click on “OK” to accept  
the default “Workgroup” as your workgroup name.  
22 To complete the installation, remove the floppy disk, and click on “Restart  
computer” in the “Windows NT Workstation Networking Setup” dialog  
box.  
23 Install the Windows NT3.51 Service Pack 5 application.  
 
11 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows NT 3.51 Workstation  
11 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows NT  
3.51 Workstation  
Connecting to a Novell Requirements  
NetWare 4.11 Server  
• HP Vectra with Windows NT 3.51 Workstation.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3ND3.SYS, version 5.26.31  
• Microsoft Windows NT 3.51 Workstation media.  
• Microsoft Windows NT 3.51 Service Pack 5.  
• Novell NetWare 4.11 Server system that supports IPX network protocol.  
• Novell IntranetWare Client for Windows NT v4.11b installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
10  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the machine and boot to a DOS bootable disk.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and reboot the system to Windows  
NT.  
 
11 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 4.11 Server  
8 Log onto Windows NT3.51 Workstation with administrator privileges  
(Contact your network administrator if you do not have the required  
information).  
9 Open the “Network” icon in the “Control Panel” program group.  
10 Click on “YES” in the “Network Settings” dialog box to install Windows NT  
Networking.  
11 Insert the Windows NT 3.51Workstation CD in the CD-ROM drive.  
12 Set the path to “D:\I386” (D:\ represents the CD-ROM drive with the  
Windows NT 3.51 CD) in the dialog-box of the Windows NT Setup window  
and click on “Continue”.  
13 Click on the “Do Not Detect” button from the “Network Adapter Card  
Detection” window, and click on the “Continue” button in the following  
“Network Adapter Card Detection” window.  
14 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer”, then click on “Continue”.  
15 Set the path to “A:\” in the “Insert Disk” dialog box, and then insert the  
3COM driver disk in the floppy drive and click “OK”.  
16 Select “3COM Etherlink (3c509) ISA Adapter” in the “Select OEM Option”  
dialog box. Click “OK”.  
17 Select ISA for the BUS Type and click on “OK”.  
18 Choose the appropriate network protocols by clicking the check boxes in  
the “Windows NT Setup” dialog box and click on the “Continue” button  
(Contact your network administrator if you do not have the required  
information).  
19 Press “OK” to continue form “Network Settings” dialog box.  
20 If applicable, press “OK” to continue from “NWLink IPX/SPX Protocol  
Configuration” dialog box.  
21 At the “Domain/Workgroup Settings” dialog box, click on “OK” to accept  
the default “Workgroup” as your workgroup name.  
22 To complete the installation, remove the floppy disk, and click on “Restart  
computer” in the “Windows NT Workstation Networking Setup” dialog  
box.  
23 From the location of the “Novell IntranetWare Client v.4.11b” install files,  
execute Setupnw.exe”.  
24 Click on the “Continue” button to proceed with the installation of the  
Novell IntranetWare Client.  
25 Click on “Yes” to agree to the Software License Agreement to begin  
installation.  
 
11 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 4.11 Server  
26 Click on the “Reboot” button to restart the machine for the changes to  
take effect.  
27 Install the Windows NT3.51 Service Pack 5 application.  
 
12 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows for Workgroups 3.11  
12 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows for  
Workgroups 3.11  
Connecting to a  
Windows NT 4.0 Server  
Requirements  
• HP Vectra with MS-DOS and MS-Windows for Workgroups 3.11.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: ELNK3.386, version 1.05.  
• Microsoft Windows for Workgroups 3.11 media.  
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink  
IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
05  
05  
I/O Address  
300  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the system and boot to MS-DOS.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and restart the system.  
8 After Windows loads, open the “NETWORK” Program Group, and double-  
click on “Network Setup”.  
9 Click on the “Networks” button in the “Network Setup” dialog box.  
 
12 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Windows NT 4.0 Server  
10 Click on the “Install Microsoft Windows Network:” option, and click “OK”.  
11 Click on the “Drivers” button from the “Network Setup” dialog box, and  
click on “Add Adapter”.  
12 Click “OK” to accept the default choice of “Unlisted or Updated Network  
Adapter”.  
13 Type the path “A:\WFW311” in the “Install Driver” dialog box, and then  
insert the 3COM 3C509B driver disk into the floppy drive, and click “OK”.  
14 Select “3COM EtherLink III (3C5X9)” in the “Unlisted or Updated  
Network Adapter” dialog box, and click “OK”.  
15 Accept the applicable network protocols, and then click on “CLOSE”.  
(Contact your network administrator if you do not have the required  
information).  
16 At the “Network Setup” dialog box, click on “OK”.  
17 Specify your User Name, Workgroup, and Computer Name in “Microsoft  
Windows Network Names” dialog box, and click on “OK”. (Contact your  
network administrator if you do not have the required information).  
18 At the “Network Setup” dialog box, click on “OK”.  
19 To complete the installation, remove the 3COM 3C509B driver disk from  
the floppy drive and click on “Restart Computer” button in the “Windows  
Setup” dialog box.  
 
13 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Microsoft Windows for Workgroups 3.11  
13 Installing the 3COM EtherLink III 3C509B ISA 10BT  
Network Adapter  
Microsoft Windows for  
Workgroups 3.11  
Connecting to a Novell Requirements  
NetWare 4.11 Server  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11.  
• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver  
disk version 6.0.  
• Driver File: 3C5X9.COM version 2.05.  
• Microsoft Windows for Workgroups 3.11 media.  
• Novell NetWare 4.11 Server system that supports IPX network protocol.  
• NetWare Client for DOS and MS Windows v1.21 installation media.  
Device Configuration  
Device Configuration  
Vectra Vli8  
Vectra VEi7  
Vectra VEi8  
Interrupt  
05  
05  
05  
I/O Address  
210  
300  
300  
Procedure  
1 With the HP Vectra turned off, install the 3COM 3C509B network adapter  
into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B network adapter.  
3 Power on the system and boot to MS-DOS.  
4 Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration”.  
6 If changes are required, save those changes and exit.  
7 Remove the 3COM 3C509B driver disk and restart the system.  
8 From the location of the “NetWare Client for DOS and Windows v1.21”  
installation files, execute “Install.exe”.  
 
13 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter  
Connecting to a Novell NetWare 4.11 Server  
9 Select option 5 “Select the driver for your network board” and press  
“Enter”.  
10 Select “OTHER DRIVERS”from the Network Board selection.  
11 Insert the 3COM 3C509B driver disk into the floppy drive.  
12 Type the path “A:\NWCLIENT” when prompted and press “Enter”.  
13 Select “3Com EtherLink III Parallel Tasking Family” and hit “Enter”.  
14 Accept the default network board settings and press “F10” to save it.  
15 Select option 6 “Highlight here and press <Enter> to install” and press  
“Enter” to begin installation.  
16 When the installation is finished, remove the 3COM 3C509B driver disk  
from the floppy drive and press <CTR><ALT><DEL> to restart the  
system.  
17 You may login to a server from the DOS prompt or load Windows for  
Workgroup v3.11 and use the “NetWare User Tools” from the NetWare  
Tools folder to login to a server. (If you do not have the required  
information, contact your network administrator).  
 
 
 

Graco Baby Carrier 5070 Series User Manual
Graco Pressure Washer 246601 User Manual
Graco Stroller 1761532 User Manual
Grundig Stereo System Weather AM FM Radio User Manual
Haier Air Conditioner 0010530627 User Manual
Harbor Freight Tools Sander 92623 User Manual
Heath Zenith Work Light UT 5676 BZ User Manual
Hotpoint Microwave Oven AHP67X User Manual
Hotpoint Oven BS41X User Manual
Hotpoint Washer AQ113F 497 I User Manual