Grizzly Marine Safety Devices T10722 User Manual

MODEL T10722/T10723  
FINGERPRINT SAFE  
INSTRUCTIONS  
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]  
Introduction  
The Model T10722/T10723 Fingerprint Safe (see  
Figure 1) provides three methods of securing  
your belongings:  
Specifications  
Overall Dimensions  
T10722.................. 1334" W x 10" H x 978" D  
T10723................. 15" W x 1134" H x 1134" D  
Maximum Fingerprints..................................... 32  
Maximum PIN Numbers .................................... 8  
Fireproof ..........................................................No  
Required Batteries.........................4 AA, Alkaline  
Biometric fingerprint verification  
PIN number  
Key  
This safe features a soft mat inside to protect  
secured items, a removable upper shelf, and  
mounting holes for securing to a wall or the floor.  
Small Item Inventory  
Description  
Protective Mat.................................................... 1  
Anchor Studs M8-1.25 x 50............................... 4  
AA Alkaline Batteries......................................... 4  
Keys................................................................... 2  
Qty  
Grizzly cannot replace lost or stolen keys.  
Please contact your local locksmith if this  
happens.  
To reduce the risk of lost or stolen keys,  
keep them in a secure location that is sepa-  
rate from the safe.  
DO NOT store keys inside safe!  
Figure 1. Model T10723 Fingerprint Safe.  
COPYRIGHT © FEBRUARY, 2013 BY GRIZZLY INDUSTRIAL, INC.  
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
FOR MODELS MANUFACTURED SINCE 01/13 #TS15619 PRINTED IN CHINA  
 
Locking Safe  
To lock the safe, make sure the dead bolts are  
withdrawn into the door, then close the door and  
rotate the door handle counterclockwise 14 turn.  
Most of the safe operations are time sensi-  
tive. In general, you will have approximately  
five seconds between finishing one action  
in the procedure and starting the next.  
Otherwise, you will have to start with Step 1  
to begin the procedure again.  
Unlocking with Fingerprint  
1. Press and release the activation button.  
Recording Fingerprint  
1. With the safe door open, then press and  
2. When the fingerprint scanner lights up, place  
your fingerprint on the scanner with medium  
pressure.  
release the reset button.  
2. Place your fingertip on the fingerprint scanner  
—If your fingerprint was verified, the green  
light will flash once, then, after a pause, will  
remain lit for approximately five seconds.  
During this time, use the door handle to  
unlock and open the door.  
with medium pressure.  
—If properly recorded, the green light will  
flash once, then, after a pause, flash again.  
—If the red and green lights flash together,  
the fingerprint was not recorded. Try again.  
—If the red and green lights flash together,  
the fingerprint was not verified. Try again.  
Recording PIN Number  
1. Press and hold the number “1” key on the  
PIN pad until the green light flashes once,  
then, after a pause, flashes again.  
Unlocking with PIN Number  
1. Use the PIN pad to enter the PIN number and  
press the activation button.  
—If the PIN number was verified, the green  
light will flash once, then, after a pause, will  
remain lit for approximately five seconds.  
During this time, use the door handle to  
unlock and open the door.  
Note: The default factory-set PIN number is  
“1234”.  
2. Enter the current PIN number and press the  
activating button.  
—If the red and green lights flash together,  
the fingerprint was not verified. Try again.  
—If the PIN number was accepted, the green  
light will flash once.  
Re-setting to Factory Defaults  
1. Open the door, then press and hold the reset  
button until the following sequence is com-  
plete:  
3. Enter the new PIN number and press the  
activation button.  
Note: PIN numbers must be 4–8 numbers in  
length.  
• One beep with a flash of the green light.  
• 15 flashes of the green light.  
4. Repeat Step 3.  
—If properly recorded, the green light will  
flash once, then, after a pause, flash again.  
• One beep with a flash of the green light.  
The safe is now set to factory defaults without any  
fingerprint scans in memory and the PIN number  
set to “1234.”  
—If the red and green lights flash together,  
the PIN number was not recorded. Try  
again.  
-3-  
Model T10722/T10723 (Mfg. Since 01/13)  
 
Mounting Safe  
The safe has holes through the back and bottom  
for mounting to a wall or floor.  
Cleaning  
Use a soft cloth moistened with warm water to  
clean the painted surfaces of the safe. Do not use  
solvents, abrasives, or spray cleaners that can  
damage the finish or electronic components.  
When mounting to a wall, we recommend secur-  
ing 1" wood stock to the wall studs, then securing  
the safe to the wood. Make sure the mounting will  
hold the weight of the safe and contents, as well  
as the forces of opening and locking the door.  
Always keep liquids away from the security pad  
and the battery compartment to prevent damaging  
the electronic components.  
Regularly clean the fingerprint scanner lens with a  
soft cloth moistened with warm water. Do not use  
paper products that can scratch the lens. Do not  
use chemicals or spray cleaners that can damage  
the lens or electronic components.  
Batteries  
The electronics of the safe are powered by four  
AA batteries. If the fingerprint scanner or PIN pad  
does not respond or if the red light on the security  
pad stays ON when attempting a procedure, the  
batteries need to be replaced.  
Use the key to open the safe and replace the  
batteries with four high-quality AA alkaline batter-  
ies. Refer to Installing Batteries on Page 2 for  
detailed instructions.  
Note: When the batteries are removed, the record-  
ed fingerprint scans and PIN number stay in non-  
volatile memory and will remain functional when  
the batteries are replaced.  
Troubleshooting  
Review the troubleshooting and procedures in this section if a problem develops with your safe. If you need  
additional help with a procedure, call our Technical Support at (570) 546-9963.  
Note: Grizzly cannot replace lost or stolen keys. Please contact your local locksmith if this happens.  
Symptom  
Possible Cause  
Possible Solution  
Security pad  
1. Batteries are low or dead.  
1. Replace batteries.  
does not properly  
respond to input;  
red light stays on.  
2. Electronic components are at fault.  
2. Replace safe or use keys to operate.  
Fingerprint scanner 1. Scanner lens is dirty.  
1. Clean scanner lens.  
will not record  
fingerprint.  
2. Fingerprint not readable.  
2. Follow the Fingerprint Scanning Tips on Page 2.  
3. Security pad memory has reached maximum 3. Erase security pad memory by re-setting to factory  
limit of 32 fingerprint scans. defaults.  
-4-  
Model T10722/T10723 (Mfg. Since 01/13)  
 

Grace Radio GDI IRA500 User Manual
Grizzly Drill G7942 User Manual
Grizzly Log Splitter H8170 H8171 User Manual
Grizzly Planer G0763 User Manual
Grundig Portable Stereo System UMS 4100 User Manual
Hamilton Beach Rice Cooker 37532 User Manual
Honeywell TV Cables 7845gsmr User Manual
HP Hewlett Packard Speaker 4274A User Manual
Husky Air Compressor A05051 User Manual
Husqvarna Snow Blower 1130SB XLSB User Manual