Graco Crib 9045 User Manual

Read all instructions BEFORE  
Failure to follow  
instructions coul  
assembly and use of this product.  
Keep instructions for future use.  
We recommend that you keep these instructions  
with your Pack ’N Play. A storage pocket has been  
provided for them on the bottom panel of your unit.  
Setting Up the Pack ’N Play  
!
THIS PRODUCT REQUIRES ADULT ASSEMBLY.  
!
Keep fingers clear of top corners during setup.  
Be sure Pack ’N Play is completely set up before use.  
Check that the four top rails are completely latched, the  
center of the floor is pushed down, and the mattress is  
flat and secured by the VELCRO® straps. Always follow  
the instructions in the owner’s manual to set up the  
Pack ’N Play.  
®
Pack ’N Play  
Bassinet  
®
!
!
When using the bassinet make sure VELCRO patches  
underneath mattress firmly attach to bassinet mesh.  
OWNER’S  
MANUAL  
Before each use, inspect this product for damaged  
hardware, loose joints, missing parts or sharp edges.  
Do not use Pack ’N Play if any parts are missing  
or broken. Call 1-800-345-4109 for replacement parts  
or owner’s manual. Do not substitute parts.  
Model No. _________  
Serial No. _________  
Using the Pack ’N Play  
Dear Customer,  
!
The Pack ’N Play can be used as a playard, bassinet or  
Please fill in the model and serial numbers  
above from the label in the center of the  
bottom of your new Pack ’N Play Bassinet.  
sleeping crib. When used as a playard, never leave child  
unattended and always keep child in view. When used as  
a sleeping crib or bassinet, you must still provide the  
supervision necessary for the continued safety of your  
child.  
Models 9045, 9046, 9346, 9640,  
9643, 9716, 9726, 9741, 9743,  
9745 & 9746  
!
Always keep the Pack ’N Play away from hazards in the  
area that may injure your child.  
!
Do not add padding or other objects inside the Pack ’N  
Congratulations on your purchase of a  
Graco® Pack ’N Play® Bassinet!  
Play that will permit your child to climb out.  
!
Stop using this product when your child reaches  
35 inches (890 mm) in height, weighs more than 30  
pounds (14 kg), or is able to climb out.  
Graco is the recognized leader in the design  
and manufacture of quality baby products.  
We believe your new Graco® Pack ’N Play®  
Bassinet is a wise choice, promising many  
hours of enjoyment for your baby.  
!
Do not modify Pack ’N Play or add any attachments  
that are not listed in the owner’s manual, including an  
add-on bassinet.  
Your Pack ’N Play® may be used as a  
playard, portable crib or bassinet.  
Using the Bassinet  
!
Use bassinet with only one child at a time.  
Customer Satisfaction  
Our goal is to make every product the best  
!
The bassinet must be fully assembled and installed,  
including top rails, snaps and bottom pad, before using.  
it can be! We are also committed to supporting our  
products after purchase. If you would like to speak  
to Graco about your product, please contact our  
Customer Service Department at 1-800-345-4109  
Our knowledgeable staff will be ready to answer  
any questions you may have concerning parts, use  
or maintenance. When you call, please have the  
model and serial numbers ready so your call  
may be processed quickly and efficiently.  
Failure to  
instructions coul  
© 1999 Graco 361-10-99  
2
 
At first your Pack ’N Play may be like a new pair of  
shoes. You may need to break it in by slightly stretching  
the netting and fabric. If the center does not stay down,  
place some weight (several books) in the center of the  
unit and let it stand overnight.  
Step 3.  
The top rail has a center piece  
with two tubes hidden under the  
fabric. The button on the bottom  
of the center piece releases the  
two tubes when it is pushed up.  
To Use as a  
Playard/Portable Crib  
Place mattress into your unit  
with padded side up.  
Center  
piece  
Always use your unit with  
mattress installed soft side up.  
Tube  
Slide the two VELCRO® straps  
through slots in bottom of Pack  
’N Play and fasten to VELCRO®  
on underside. This will prevent  
mattress from moving.  
Push UP button  
under fabric  
Your Pack ’N Play is ready to  
use.  
To fold the top rail:  
!
Lift up slightly on the top rail.  
!
Push up on the button located under  
®
!
To Fold Your Pack ’N Play  
the symbol to release the two tubes.  
!
Push down.  
Step 1.  
HINTS:  
Lower the back flap. Apply  
locks on wheels or casters,  
if present. Release the two  
VELCRO® straps under the  
Pack ’N Play, and remove the  
mattress.  
!
If top rails do not unlatch, lift  
the center of the floor higher.  
!
!
Both tubes must be released  
for the top rail to fold.  
!
Step 2.  
IMPORTANT:  
Step 4.  
Raise center halfway  
BEFORE unlocking  
rails.  
Pull center up all the way.  
Grasp the red handle  
on the center of the floor  
as shown.  
Push down and turn  
handle. Then pull up  
approximately halfway  
to the top rails.  
361-10-99  
5
6
 
®
To Cover Your Pack ’N Play  
Step 5.  
Gather your unit together.  
Do not force.  
Models with changing table and wheels:  
If unit will not fold, look for a  
partially latched top rail. Squeeze  
the latch button to release the rail.  
Pull the cover over your unit  
as shown, making sure carry  
handle attached to Pack ’N  
Play mattress is lined up with  
zipper.  
Before pulling bag up, insert  
folded changing table into the  
side opposite the handle as  
shown. Pull bag up to cover  
Handle  
end. Zip together.  
Step 6.  
Find the bottom corner belt loop  
(only one). This loop is for holding  
unit and mattress together while  
carrying.  
Models with wheels only:  
Wheel  
Foot  
Turn unit upside down, so that  
wheels point up. Pull the cover  
over your unit. Make sure carry  
handle attached to Pack ’N  
Play mattress is lined up with  
zipper.  
Step 7.  
Handle  
Wrap the mattress around your unit.  
Fasten together the VELCRO® straps,  
attaching the bottom strap to the  
bottom corner belt loop.  
Push the plastic end of the bag  
over wheels and feet. Turn unit  
over and pull bag up to cover  
end. Zip together.  
Models with feet or  
casters and feet:  
Pull cover over your  
unit. Be sure carry  
handle attached to  
Pack ’N Play mattress  
is lined up with zipper.  
Turn unit over. Pull bag  
up to cover end. Zip  
together.  
CARE AND MAINTENANCE  
FROM TIME TO TIME CHECK YOUR PACK ’N  
PLAY for worn parts, torn material or stitching.  
Replace or repair the parts as needed. Use only  
Graco® replacement parts.  
IF PACK ’N PLAY IS USED AT THE BEACH, you  
MUST clean sand off your Pack ’N Play, including  
the feet, before packing it into cover. Sand in top  
rail lock may damage it.  
On certain models:  
TO CLEAN PACK ’N PLAY, use only household  
soap or detergent and warm water.  
The cargo bag opens on either end. Slip the bag over  
the Pack ’N Play. Check that the carrying handle  
attached to the Pack ’N Play mattress sticks out the  
hole in the bag. Zip both ends.  
TO WASH CARRY BAG AND FITTED SHEET,  
machine wash in lukewarm water on delicate  
cycle and drip-dry. NO BLEACH.  
7
8
 
Step 4.  
BASSINET INSTRUCTIONS  
PARTS LIST  
Install the end of the tube  
without the red spring latch  
by placing the loop end into  
the slot in the plastic corner.  
CHECK that you have all the parts listed below  
BEFORE assembling your bassinet.  
Step 5.  
No tools required.  
On the other end of the tube,  
pull back on the red spring  
latch and insert the loop into  
the slot in the plastic corner.  
The loop ends must be in the slots in the  
corners to secure the bassinet in the Pack ’N Play. Pull  
up on the tube and bassinet to ensure that the tube is  
in place.  
Bassinet  
Loop end  
Tube (2)  
Tube (2)  
Wire end  
Step 6.  
Repeat steps 4 and 5 on the  
other side of the bassinet.  
Round end  
Red spring  
latch end  
Step 7.  
To Install Your Bassinet  
Snap both of the end flaps of  
the bassinet to the Pack ’N  
Play with the eight snaps  
(four on each end).  
The four bassinet tubes are located in storage pockets  
sewn into the bassinet itself.  
Step 8.  
Step 1.  
Place the mattress in the  
bassinet soft side up. Push  
down on the mattress to  
secure the mattress to the  
VELCRO® on the bassinet.  
Insert wire end of one tube  
into the round end of a tube  
with a red spring latch.  
Repeat with other tubes.  
DO NOT use your bassinet  
without the mattress  
provided by Graco.  
Step 2.  
Slide the assembled tubes  
into the tunnels on the sides  
of the bassinet.  
To avoid SUFFOCATION, DO NOT use  
extra padding such as a water mattress, mattress, or  
pillows inside the bassinet. Use ONLY mattress  
provided by Graco.  
Step 3.  
Lift bassinet by the two tubes and lower it into the  
Pack ’N Play. Make sure the printed warnings on  
the end flap are facing up.  
Your bassinet is now ready to use.  
361-10-99  
9
10  
 
To Remove Your Bassinet  
Casters*  
To apply the locks, push  
DOWN on the levers.  
Step 1.  
Remove the mattress from your bassinet.  
Step 2.  
To release the locks, lift UP  
on the levers.  
Unsnap the end flaps from your Pack ’N Play.  
Step 3.  
Pull back the fabric at one corner of the bassinet to find the  
red spring latch.  
Wheels*  
Step 4.  
To apply the locks, push  
DOWN on the levers.  
Pull the red spring latch back  
and lift up the tube.  
To release the locks, lift UP  
on the levers.  
Step 5.  
Pull the tube out of the bassinet  
and set aside.  
Parent Organizer*  
Always keep objects out of child’s  
reach. Remove parent organizer when child is able  
Step 6.  
Repeat steps 3, 4 and 5 to remove the other tube.  
to pull himself up in the Pack N Play.  
Step 7.  
Step 1.  
Use extreme  
care when pulling the tubes  
apart.  
Your parent organizer  
includes two plastic dividers.  
Slide the plastic dividers  
into the two pockets in the  
section dividers of the  
parent organizer.  
Pull the tubes apart by twisting  
the tubes as you pull. Store the  
tubes in the pockets in the  
bassinet.  
Step 2.  
ACCESSORY INSTRUCTIONS  
ON CERTAIN MODELS*  
Slide the tube into the  
mounts on the end of  
your unit.  
Side Flap*  
Push the button in to  
get it started.  
You can raise side flap if desired.  
Unfasten VELCRO® straps at  
bottom of flap. Roll flap up.  
Fasten in place with snap loops at  
top.  
Pull up on the parent  
organizer to make sure  
that the buttons are  
caught on the bottom  
of the mounts.  
Button  
Step 3.  
Cargo Bag*  
To remove the parent  
The cargo bag can be snapped  
onto the end of the Pack ’N Play  
for easy access. Unzip both ends  
and tuck inside the bag.  
organizer push in on the  
buttons on the bottom of  
the tubes and pull up.  
Maximum weight 5 lbs (2.3 kg).  
11  
12  
 
Step 1.  
CHANGING TABLE INSTRUCTIONS  
(ON CERTAIN MODELS)  
Lay changing table flat on floor with short side in front  
of you and belt facing up. Gently slide one long tube into  
opening on long side exactly as shown.  
Parts List  
CHECK that you have all parts listed below  
BEFORE assembling your changing table.  
Long  
side  
Repeat on other side.  
No tools required.  
Long tube (2)  
Short tube (2)  
Short side  
Step 2.  
Slide one short tube  
into opening on end  
as shown.  
For proper orientation,  
be sure folding side of  
hinge faces pad as  
shown.  
Changing pad  
Changing  
table  
Fold side  
of hinge  
DO NOT insert  
other short tube  
at this time.  
Accessory bag  
Step 3.  
To Use Your Changing Table  
Turn up long tube so  
that its end points down.  
To protect your child from falls and  
other injuries:  
Insert end of long tube  
into opening on end of  
short tube as shown.  
DO NOT slide short  
tube up around the bend  
of long tube until you  
• Always stay within arm’s reach of your child when  
using the changing table. Always use waist belt  
when child is on the changing table. Never leave  
child unattended.  
Short tube side  
have finished next step.  
• The changing table is designed for use only with  
this Graco Pack ’N Play. Do not attempt to use it  
with any other product. Before each use, make  
sure the changing table is properly secured to  
the Pack ’N Play by pushing down firmly in the  
middle of the changing table. The changing table  
should not fall.  
Make sure fabric does  
not get caught in  
opening when inserting  
long tube into short tube.  
Step 4.  
• Do not use the changing table as a sleeping or  
play area.  
Repeat step 3 on other  
end of short tube, then  
slide short tube ends up  
onto long tubes.  
• Weight limit for the changing table is 25 pounds  
(11.3 kg). Do not use the changing table as extra  
storage. Always remove the changing table when  
your child is in the Pack ’N Play.  
TO AVOID TEARING  
FABRIC, slide this end  
up before proceeding  
with step 5.  
• The Pack ’N Play changing table can be used on  
the floor without being attached to the Pack ’N  
Play. Never place the changing table on a piece of  
furniture, bed, counter or any raised surface from  
which the changing table or your child could fall.  
Slide ends up  
361-10-99  
13  
14  
 
Step 5.  
To Use Accessory Bag  
Repeat steps 2  
and 3 on other end  
of changing table.  
If your bassinet is already installed, unsnap the four  
snaps on the bassinet end flap from either end of  
Pack ’N Play.  
If the short tubes  
have been inserted  
correctly, the changing  
table should be able  
to FOLD UP in the  
center as shown.  
Step 1.  
Snap accessory bag  
onto end of Pack ’N  
Play with four snaps  
as shown.  
Fold up  
Step 6.  
Place pad in changing  
table with vinyl side up.  
Pull belt straps through  
holes in center of pad.  
Step 2.  
Snap bassinet end flap  
over the accessory bag  
with the four snaps.  
Step 7.  
To Fold Changing Table  
Insert VELCRO® straps  
into the four slots at the  
corners of changing table  
and attach to VELCRO®  
on underside of changing  
table. This will prevent  
pad from moving.  
Step 1.  
Pull up on waist belt  
straps to fold.  
Step 2.  
Step 8.  
Ends of long tubes  
must point up when  
folded as shown.  
Place changing table on  
Pack ’N Play as shown.  
You may use your changing  
table with or without your  
bassinet installed. Make  
sure tubes are securely  
over the sides of the  
Ends of tubes  
point up  
Pack ’N Play.  
Check that the changing  
table is supported  
by the Pack ’N Play by  
pushing firmly down into  
center of changing table.  
Step 3.  
To carry or store your changing table  
with your folded Pack ’N Play, see  
To Cover Your Pack ’N Play” section  
in these instructions.  
15  
16  
 
Replacement Parts  
Instructions for ordering Pack ’N Play® parts:  
Complete form below. Your Pack ’N Play model number  
MUST be included on the form to ensure proper replacement  
parts. Your model number can be found on a label on the  
center of the bottom of the unit. Payment must accompany  
your order.  
Parts List:  
Price:**  
Mattress ......................$17.50  
Carry bag ................... $15.00  
Cargo bag* ................. $15.00  
Caster assembly* ....... $ 5.00 (each)/$8.00 (2)  
Wheels* ...................... $ 7.00 (each)/$10.00 (2)  
Fitted sheet ................ $10.00  
Bassinet parts:  
Bassinet ......................$17.00  
Wire end tube .............$ 5.00  
Round end tube ..........$ 5.00  
Changing table parts:  
Long tube* .................. $ 9.00  
Short tube* ................. $ 7.00  
Changing pad* ........... $10.00  
Changing table* ..........$15.00  
Accessory bag* .......... $ 7.00  
* On certain models  
** Prices subject to change without notice.  
IF YOU NEED HELP  
If you have any questions or if you need any part not list-  
ed, please call toll-free:  
1-800-345-4109  
Return the form below with payment to:  
GRACO CHILDREN’S PRODUCTS INC.  
CUSTOMER SERVICE DEPARTMENT  
P.O. BOX 100, MAIN STREET  
ELVERSON, PA 19520  
Model Number  
SHIP TO:  
(Must be filled in)  
Name  
Mattress  
Carry bag  
Cargo bag  
Address  
Caster assembly  
Wheels  
City, State, Zip  
Fitted sheet  
Bassinet  
Wire end tube  
Round end tube  
Long tube  
(
)
Telephone  
Check enclosed  
(payable to Graco Children’s  
Products Inc.)  
Short tube  
Changing pad  
Changing table  
Accessory bag  
Charge to credit card:  
Visa  
MasterCard  
Discover  
Total:  
Shipping  
& handling:  
$5.00  
Account #:  
6% sales tax  
(PA only):  
Expiration date:  
Signature:  
Total amount  
due:  
361-10-99  
17  
 

Grizzly Saw G8994z User Manual
Grundig Car Stereo System EC 4700 RDS User Manual
Grundig Flat Panel Television ROM 26 CLE 8100 BG User Manual
Harbor Freight Tools Automobile Parts 94487 User Manual
Harman Kardon Speaker System HKTS 15 User Manual
Harman Kardon Turntable CDR 26 User Manual
Hatteras Hammocks Baby Swing Single Cotton Rope Swing User Manual
Humax Flat Panel Television LP32 TDR1 User Manual
Humminbird Fish Finder 586c User Manual
IDEAL INDUSTRIES Automobile Accessories S 00 S 10011 User Manual